2in1 mini Magnetic Screwdriver - double Phillips and flat tip - Multitool

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on

This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately.
The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue).
These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package.
Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors.

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

3-axis analog accelerometer module based on the MMA7361 sensor. The built-in sensor has a low demand for electricity. The measuring range of the sensor can be changed between two ranges ± 1.5 g and ± 6 g. The selection is made using a digital input or welded bridges.
MMA7361 Triple Axis Analog Accelerometr features:
MMA7361 3-axis analog accelerometer Supply voltage: 3.3 - 5 V (built-in RT9161 chip) Measuring range selected from the IO line of the microcontroller or via bridges Comparators with hysteresis for CMOS / TTL 3.3 V, 5 V inputs Pin pitch: 2.54 mm Dimensions: 28 x 17 mm.        Helpful links - MMA7361 datasheet

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

3x DC PCB Socket Connector 5.5 x 2.1 features:
- Type: DC female jack
- Diameter of the pin: 2,1mm
- Diameter of the connector: 5.5mm
- Quantity: 3 units