8in1 ballpoint screwdriver - with straight and cross head The 8in1 Pen Screwdriver is a practical set containing 8 straight and Phillips screwdrivers for screwing and unscrewing various screws. The screwdriver is equipped with a detachable tip in which all the bits are stored. Code H0556 Available Regular price €2.88 -€1.00 Price €1.88
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Last items in stock Price €14.04
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 ✗ Out-of-Stock Price €1.61
Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs - Ideal for fix on the axis of the motors of your 3D printer Code I0004 Backorder Regular price €1.61 -€0.50 Price €1.11
Resistor 2K Ohm 5% 0,25W 1/4W Resistors 2K Ohm 5% 0,25W 1/4W features:-2 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0014 Available Price €0.07
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.15
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €5.36 -€2.00 Price €3.36
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €5.70
SparkFun RedBot Sensor - Accelerometer The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements. Code SP078 Available Price €7.43
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €2.55
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Last items in stock Price €12.39
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €14.04
SparkFun Triple Axis Accelerometer Breakout - ADXL335 This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino Code SP002 Available Price €18.17
SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €15.66
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Last items in stock Price €14.04
SparkFun RedBot Sensor - Accelerometer The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements. Code SP078 Available Price €7.43
ADXL345 3-Axis Accelerometer SPI and I2C Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features: - Type: 3-axis accelerometer- Chip: ADXL345- Supply voltage: 3-5V- Consumption: 40uA active and 0.1uA on hold- Communication: SPI and I2C- Measurements: Static and dynamic acceleration- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g- Resolution: 13 bits- Dimensions: 20x16mm- Operating temperature: -40 °C to +80 °C- Detection: Free fall, click-double click Code M0018 Available Price €2.55
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Last items in stock Price €12.39
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €14.04
SparkFun Triple Axis Accelerometer Breakout - ADXL335 This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino Code SP002 Available Price €18.17
SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €15.66
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Last items in stock Price €14.04