everActive 18650 3.7V Li-ion 3200mAh micro USB battery with protection box

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

This module includes the component BME280 that is translated into a digital signal.
The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.
Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features:
- Interfaces:
- I2C (up to 3.4 MHz)
- SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
- Temperature: -40ºC to + 85ºC
- Humidity: 0-100%
- Pressure: 300-1100 hPa
- Resolution of the measures:
- Temperature: 0.01ºC
- Humidity: 0.008%
- Pressure: 0. 18Pa
- Accuracy of the measures:
- Temperature: +/>

Version compatible with Arduino Nano V3.0
It has an ATMega328P chip running at 16Mhz with bootloader loaded factory.
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per I / O pin 40 mA
- Flash memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Frequency Clock: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

Gear Reducer Motor 6V DC 200RPM for Smart Car features:
- Voltage: 3 to 6V DC
- Speed without load: 200 RPM to 6V DC
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles
- Wiring of the 6V DC 200 RPM motor with the L298N double bridge H controller module

It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip.
The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed.
Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC
- Operating current: 45 mA
- Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds
- Navigation update: 5 Hz max. (1 Hz default)
- Capture time: at the beginning 27s, in operation 1s
- Operating temperature: -40 ° C - + 85 ° C
- separate GPS antenna 18x18 mm - Size: 22x30x13 mm

The novelty of micro:Bit v2.2 for a more lively introduction to technology for children.

The micro:bit is a pocket computer that can be encoded, customized and controlled for the implementation of digital ideas and games. It measures just 4x5cm and features a fun and easy to use design, so users can create anything from games and animations to slick stories at school, at home or anywhere - all it takes is imagination and creativity. It is fully programmable. This means that each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer, Bluetooth 5.0 technology, microphone and speaker.

It contains a quick start guide in the same package.

Screw Shield V1- Arduino ScrewShield UNO y MEGA features:
Screw Shield V1 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate
- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more.

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /