Liquid Flux for Alcohol-Based Rosin Welding 15ml

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

AC-DC to DC converter from 230V to 5V equipped with a housing.

Type of chemical preparation: alcoholic stripper of printed PCB plates.
Alcohol-based cleaner to eliminate fluxes, dirt removal, flux residues in PCB.
has low impact on electronic components.
Alcohol PCB Cleaner 1l features:
- Form: liquid
- Capacity: 1l
- Alcohol PCB cleaner
PCB cleaner based on alcohol for the elimination of any residue from the printed circuit surfaces after welding, cleaning of the welding unit frames, templates and rosin screens, and the dissolution of the waste stream.
The liquid does not affect the substrate or components of the circuit board.

Tin ideal for application in consumer electronics circuits
Tin Roll 60/40 Sn/Pb 2.5% Flux 10g 1mm features:
- 10 gr. welding wire of 1 mm diameter. 60% tin, 40% lead
- Melting temperature 187/190 C
- Alloy Sn60Pb40
- Flux 2.5% SW26 1.1.2B ISO9454 - It is leaded alloy for manual and automatic processes where meeting the requirements of the RoHS2 Directive is not required.  - Quantity: 1 unit
- High quality - manufactured in EU

It is used to pass the current, power electrical and electronic circuits, fans, motors, among others. Black Crocodile Clip KK1 with Banana Plug features:
- Total length: 53 mm
- Handle length: 34 mm
- Color: Black
- Banana shot: yes
- Isolated terminals: yes
- Maximum opening: Around 9 mm
- Conductive material: Nickel-plated steel
- Includes 1 unit

Transistor kit, 200pcs of PNP+NPN TO-92 Bipolar Transistor in a box.

BC337, BC327, 2N2222, 2N907, 2N3904, 2N3906, S8050, S8550, A1015, C1815.

Well packed and assorted in a plastic storage case. It's a great choice for your electronic projects.

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
The display module 4-digit LED with TM1637.
The unit can be controlled with just two DIO and CLK control lines.
TM1637 4-Digit Digital Display Module features:

- 3V-5V supply voltage
- Current consumption 250 mA
- 7-segment display 4 digits common anode
- Digit size: 0.36 inches
- Dimensions: 42x24x11mm