HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
Mini Prototype Plate of 6 Unds Various Colors Kit without Solder 25 Points for Arduino Mini plate to develop simple test projects for the arduino without requiring component soldering.It exists in 6 colors. Mini Prototype Plate of 6 Unds Various Colors Kit without Solder 25 Points for Arduino features: - Plastic material- Color: exists in white / yellow / black / red / green / blue- Number of LED diodes: 300 diodes / 5m (60 diodes / m)- Size: Approx. 2x1.5x1.2cm / 0.79x0.59x0.47 "- Emitted colors: RGB color variations- 100 new and high quality- Practical and useful- Prototype without welding with 25 points- Completely reusable and with self-adhesive backing- Easy component placement Code PB027 Available Price €3.00
2x Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor 2x Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm - Quantity: 2 units Code S0026 Available Price €0.50
Kit 2x Blue Aluminium and Gold flat metal heatsinks For Raspberry Pi 2 and Pi 3, B and B +. Each heatsink includes thermal sticker. Kit 2x Blue Aluminium and Gold flat metal heatsinks features: 1 blue aluminum heatsink: - Dimensions: 9x9x12mm 1 flat metal sink gold color: - Dimensions: 12x12x1mm Code RA022 Available Price €1.49
TDA2030A 1X18W Audio Amplifier TDA2030A 1X18W Audio Amplifier features: - Chip: TDA2030A - Power supply: DC 6V ~ 12V - Channel type: Single channel - Output power: 1 x 18 W - Output output: 4 ~ 8 Ohm - Mono mode - Size (LxWxH): 31.6 x 23.5 mm Code M0063 Available Price €3.39
5x L7805 Voltage Regulator 5V 1.5A TO-220 5x L7805 Voltage Regulator 5V 1.5A TO-220 features:-Type Output: Fixed-Voltage Output: 5V-Manufacturer: ST Microelectronics-Output current: 1.5A-Max input voltage: 35V-Input input min.: 5V-Operational temperature: 0ºC to + 125ºC-Encapsulated: TO-220-Polarity: Positive Code T0022 Available Price €0.39
Power Supply Transformer 220V AC/DC 2A 5V Power Supply Transformer 220V AC/DC 2A 5V features:- Input voltage: 100~240V 50Hz- Output voltage: DC 5V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0102 Available Price €3.99
40x Male to male cables 20cm Characteristic: -Length: 20cm -Quantity: 40 cables -Mono Dupont connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0006 Available Price €2.49
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Price €9.60
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €9.90
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €9.90
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Available Price €9.99
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €7.90
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €7.99
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Backorder Price €22.90
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.95
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Price €24.90
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Price €9.60
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €9.90
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €9.90
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Available Price €9.99
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €7.90
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €7.99
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Backorder Price €22.90
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.95
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Price €24.90