Pliers Front Cut 110mm

- It consists of a 20-character, 4-row display
- The display is compatible with the controller HD44780 and integrates the module so you can use it through the I2C protocol without any problem
- Only two pins are needed for communication, SDA and SCL
- Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32
PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F
- It can be changed to any between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2
20x4 2004 LCD display PCF8574T I2C Backlit Blue features:

- LCD screen, 20 characters and 4 lines
- 5V power supply
- HD44780 compatible controller

- Tensión de alimentación: 110/230V AC
- Tensión de salida: 24V DC
- Amperaje de salida: 5A
- Potencia a 24V: 120W
- Dimensiones: 160mm x 99mm x 43mm

The cables are in 10 different colors Flat Cable 1m AWG28 1.27 10 Pins Colors features:
- Length: 100cm
- Model AWG28
- Product name: Flat cable
- Number of conductors: 10
- Conductive material: Copper
- Insulation voltage: 300V - Inner diameter 0.32mm
- Pin Pitch: 1.27mm
- Temperature: 105 ° C

Connector BLS04 Female / Female 4 Pins RoHS Single Row features:
- Step between pins: 2.54 mm
- Manufacturer: Maritex
- Number of connections: 4 in a single row
- Type: Female / Female
- RoHS standard

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 20-30LM
- Ã beam angle: 120 degrees
- Color emission: blue

20 Mini Jumpers 2.54mm Short Circuit Board PCB features:
- Mini standard 2.54mm jumpers for making short circuit bridges on printed circuit boards, hard disks, PCBs, etc.

Connectors 10x BLS05 Female/Female 5 Pins RoHS Single Row features:
- Step between pins: 2.54 mm
- Manufacturer: Maritex
- Number of connections: 5 in a single row
- Type: female / female
- RoHS standard