Servo Micro Digital Symmetry Left 1.5g 4.8V

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART).

Resistor 100K Ohm 5% 0,25W 1/4W features:
 100K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

6 DIP pins and 2 positions DPDT. This switch is widely used to control the operation of many small electronic power projects, including volume and other controls for audio video, dimmer controls for lights.
It is also a great component for DIY. Vertical Slide Switch 2P2T 50V 0.5A features:
- Type: 2P2T
- Contact resistance: 30 MΩ max.
- Insulation resistance: 100 MΩ
- Maximum operating voltage: 50V
- Maximum operating current: 0.5A
- Can support 500 VAC for 1 minute
- Step between pins: 2.54mm / 0.1 "
- Pin size: 4.5x0.5x15 / 0.77 "x0.19"
- Type of current: DC
- Pins to be welded
- Switch action: 2 ON / OFF positions
- Shape of interrupter: rectangular
- Size: 16x6.5x15 / 0.2 "x0.02"

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

5x Push Switch Button B3F Omron Blue Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed