LCD TFT Touch Screen Display 3.2 Touch 320x240

TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:
- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board
- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.
- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32
- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.
- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen.

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:
- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board
- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.
- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32
- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.
- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen.

LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:
- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3
- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board
- Put the screen on the shield and you can connect it directly to the Arduino UNO
- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32
- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top
- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen

LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:
- LCD screen TFT 240x320 pixels
- Power 2.8-3.3V
- 262,000 possible colors (18 bit)
- 8/16 bit parallel bus digital interface
- LCD Controller: ILI9325
- Touch screen controller: XPT2046
- Touchscreen, resistive touch screen
- Manual use or with any type of pointer
- SD card reader
- Connector: 2 x 20 pins 2.54mm
- Dimensions PCB 75x55 mm
- Dimensions LCD 59x42 mm
- Ideal for projects with ARDUINO Uno Mega, AVR, STM

LCD TFT Display Module 240x320 2.4 SPI features:
- LCD screen TFT 240x320 pixels
- 262,000 possible colors (18 bit)
- Pixel: RGB vertical band
- Driver ILI9341
- SPI interface
- 8-bit digital interface, 4-bit control lines
- Resistive touch screen 4 - cables
- Ideal for projects with ARDUINO, Uno R3, MEGA2560
Helpful Links:
Wiring of the TFT LCD screen 2.4 SPI
- Connect the TFT 2.4 SPI LCD screen with the UNO module
Display graphics and texts on the LCD TFT screen 2.4 SPI
Program a touch calculator on the LCD screen TFT 2.4 SPI

1.44 inch TFT LCD screen 128x128 SPI features:
- TFT LCD screen 128x128 pixels
- 4-wire SPI interface (A0, SDA, SCK, CS)
- Size: 1.44 inches
- Interface: SPI
- Resolution: 128 * 128
- Visual area: 1: 1 square
- Color screen TFT, the effect is much better than other small CSTN displays
- Disk drive: ST7735
- Fully compatible and alternative 5110 interface
- Onboard LDO, 5V / 3.3 input voltage support V
- Screen dimensions: 30 x 28 mm
- PCB dimensions: 45 x 32 mm

LCD TFT Touch Screen Display 3.2 Touch 320x240 features:
- TFT LCD screen 320x240 pixels
- 3.3V 5V power
- 262,000 possible colors (18 bit)
- 8/16 bit parallel bus digital interface
- LCD driver: ILI9341
- Touch screen controller: XPT2046 o ADS7843: 4-Wire Touch
- Touchscreen, resistive touch screen
- Manual use or with any type of pointer
- SD card reader

- Shield 40pins
- Connector: 2 x 17 pins 2.54mm
- PCB dimensions 95x65 mm
- Dimensions LCD 57x79 mm
- Ideal for projects with Arduino Uno Mega, AVR, STM

- Pantalla LCD TFT 240x320 pixels
- 262.000 posibles colores (18 bit)
- Pixel: RGB vertical stripe
- Controlador ILI9341
- Interface SPI
- 8 bit interfaz digital, 4 bit líneas de control
- Pantalla táctil resistiva 4
- wires
- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI
- Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI

1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.
Easily programmable with UNO module, Arduino, Raspberry, Mega2560.
LCD TFT Display Module 128x160 1.8 SPI features:
- TFT LCD screen 1.8 128x160 pixels
- Pixel: RGB vertical stripe
- Driver ILI9163,
- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)
- 5-pin interface CS, RS, SCL, SDA, RST for control
- Resistive touch screen
- Ideal for projects with ARDUINO, Uno R3, MEGA2560

TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:
- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board
- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.
- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32
- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.
- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen.