Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Last items in stock Price €7.95
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €3.49
Embellisher Button Red White Yellow Orange Potentiometer Knob for Arduino Embellisher features:- Color black and red, white, yellow, orange- Upper diameter: 0.9 cm- Lower diameter: 1.5 cm- Height: 1.6 cm- Inside hole diameter: 0.6 cm Code K0061 Available Price €0.69
16x2 1602 LCD display HD44780 Backlit Blue background It consists of a 16-character, 2-row display. The display is compatible with the HD44780 controller. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. 16x2 1602 LCD display HD44780 Backlit Blue background features: - LCD screen , 16 characters and 2 lines - 5V power supply - HD44780 compatible controller - Backlit blue background, white letters - Include an adjustable contrast pin - Dimensions (mm): 80 x 36 x 12 Code P0014 Available Regular price €2.65 -€0.75 Price €1.90
Protoboard Breadboard 9x15cm Protoboard Breadboard 9x15cm features: -PCB dimension: 9x15cm-Hole diameter: 1mm -Pitch: 2.54mm-Bakelite with copper fields Code PB016 Available Price €0.75
Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY features: - Mounting kit - Ceramic Peltier Cell 12V TEC1-12706 - Heatsink 12x10x25mm (hot side) - Heatsink 60x40x25mm - Color black or silver - Thermal insulation 70x65mm for cell - Fan 12V 90x90x25mm with grille - Thermal paste 0.5g - Screws - Peltier effect cell model TEC1-12706, 12v, max. 60w and 6A, with a temperature difference between their faces of up to 67ºC - Max Power: 60w - Voltage: 12v - Max Voltage: 15.2v - Max Current: 6A - Temperature Variation: Code M0059 Available Price €18.79
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Voltmeter LED Waterproof Digital Display DC Green 3.5V 30V DC 0.56 Voltmeter LED Waterproof Digital Display DC Green 3.5V 30V DC 0.56 features:- Measuring range: from 3.5 VDC to 30 VDC ±% 1- Operating current: <30mA- Measuring refresh time: 500ms- Dimensions: 54mm x24mm x15mm- Cable length: 85 mm- Color: Black- Display: Green LED- Operating temperature: -10ºC to 65ºC Code M0037 ✗ Out-of-Stock Regular price €3.99 -€1.00 Price €2.99
Voltmeter Amperemeter DC Red and Blue 100V 10A Voltmeter Amperemeter DC Red and Blue 100V 10A features: - Supply voltage: 4.5V to 30V - Voltage measurement range: 0V to 100V (± 1%) - Min voltage resolution: 0.1V - Current measurement range: 0A to 10A (± 1%) - Min current resolution: 0.01A - Operating current: 5mA to 15mA - Display: Red LED color (Voltage) and Blue LED color (Intensity) - Includes reverse polarity protection - Measurement refresh time: 500ms - Screen dimensions: 48 x 29 mm - Recessed hole: 45.5 x 26.5 mm - Depth: 21 mm - Cable length: 150 mm - Operating temperature: - 10ºC to 65ºC - No battery needed - Dual panel with voltmeter and digital ammeter Code M0068 Available Price €3.99
Shunt Resistor Ammeter DC 50A 75mV Shunt Resistor Ammeter DC 50A 75mV features: - Dimensiones 12x2.5x1.8 cm Code M0074 Available Price €2.99
Digital Voltmeter Red 0V to 30V DC 0.56 Digital Voltmeter Red 0V to 30V DC 0.56 features: - Measurement range: 0-30 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Red Led - Color: black - Includes reverse polarity protection - Operating current: Code M0065 ✗ Out-of-Stock Price €2.59
Mini voltmeter with LED display 7 blue segments 3 digits 3.5-30 VDC - 1% Mini voltmeter with LED display 7 red 3-digit segments.Simply connect the positive and the negative to turn it on and measure the voltage. Mini voltmeter with LED display 7 blue segments 3 digits 3.5-30 VDC - 1% features: - Operating voltages (measurement): 3.5 - 30 VDC,- Color of the LED segments: blue- Update speed: approx. 500ms,- Accuracy of the measurement: ± 1%,- No need power supply: it is powered with the measured voltage,- Cable length included: 10cm,- Size: 30x12x9mm. Code M0201 Available Regular price €2.50 -€0.50 Price €2.00
USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €5.95
Digital Voltmeter Green 0-200V DC 0.56 Digital Voltmeter Green 0-200V DC 0.56 features: - 3-wire recessed LED Voltmeter - No battery needed - Measurement range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Green Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0046 ✗ Out-of-Stock Regular price €2.79 -€0.50 Price €2.29
Current and Voltage Meter Tester Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets.The voltage and current are shown successively.Current and Voltage Meter Tester features:- Operating range: - Voltage 3 - 7,5V - Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%%- Dimensions: 5.2 x 2 x 1.5 cm Code K0081 Available Price €2.89
Voltmeter DigitaI Blue 0-200V DC 0.56 Voltmeter DigitaI Blue 0-200V DC 0.56 features: - 3-wire recessed LED Voltmeter - No battery needed -Measuring range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Blue Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0045 Available Price €2.99
Digital Voltmeter Red 0-200V DC 0.56 Digital Voltmeter Red 0-200V DC 0.56 features: - No battery needed - Measurement range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Red Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0047 Last items in stock Price €2.59
Voltmeter LED Waterproof Digital Display DC Green 3.5V 30V DC 0.56 Voltmeter LED Waterproof Digital Display DC Green 3.5V 30V DC 0.56 features:- Measuring range: from 3.5 VDC to 30 VDC ±% 1- Operating current: <30mA- Measuring refresh time: 500ms- Dimensions: 54mm x24mm x15mm- Cable length: 85 mm- Color: Black- Display: Green LED- Operating temperature: -10ºC to 65ºC Code M0037 ✗ Out-of-Stock Regular price €3.99 -€1.00 Price €2.99
Voltmeter Amperemeter DC Red and Blue 100V 10A Voltmeter Amperemeter DC Red and Blue 100V 10A features: - Supply voltage: 4.5V to 30V - Voltage measurement range: 0V to 100V (± 1%) - Min voltage resolution: 0.1V - Current measurement range: 0A to 10A (± 1%) - Min current resolution: 0.01A - Operating current: 5mA to 15mA - Display: Red LED color (Voltage) and Blue LED color (Intensity) - Includes reverse polarity protection - Measurement refresh time: 500ms - Screen dimensions: 48 x 29 mm - Recessed hole: 45.5 x 26.5 mm - Depth: 21 mm - Cable length: 150 mm - Operating temperature: - 10ºC to 65ºC - No battery needed - Dual panel with voltmeter and digital ammeter Code M0068 Available Price €3.99
Shunt Resistor Ammeter DC 50A 75mV Shunt Resistor Ammeter DC 50A 75mV features: - Dimensiones 12x2.5x1.8 cm Code M0074 Available Price €2.99
Digital Voltmeter Red 0V to 30V DC 0.56 Digital Voltmeter Red 0V to 30V DC 0.56 features: - Measurement range: 0-30 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Red Led - Color: black - Includes reverse polarity protection - Operating current: Code M0065 ✗ Out-of-Stock Price €2.59
Mini voltmeter with LED display 7 blue segments 3 digits 3.5-30 VDC - 1% Mini voltmeter with LED display 7 red 3-digit segments.Simply connect the positive and the negative to turn it on and measure the voltage. Mini voltmeter with LED display 7 blue segments 3 digits 3.5-30 VDC - 1% features: - Operating voltages (measurement): 3.5 - 30 VDC,- Color of the LED segments: blue- Update speed: approx. 500ms,- Accuracy of the measurement: ± 1%,- No need power supply: it is powered with the measured voltage,- Cable length included: 10cm,- Size: 30x12x9mm. Code M0201 Available Regular price €2.50 -€0.50 Price €2.00
USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €5.95
Digital Voltmeter Green 0-200V DC 0.56 Digital Voltmeter Green 0-200V DC 0.56 features: - 3-wire recessed LED Voltmeter - No battery needed - Measurement range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Green Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0046 ✗ Out-of-Stock Regular price €2.79 -€0.50 Price €2.29
Current and Voltage Meter Tester Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets.The voltage and current are shown successively.Current and Voltage Meter Tester features:- Operating range: - Voltage 3 - 7,5V - Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%%- Dimensions: 5.2 x 2 x 1.5 cm Code K0081 Available Price €2.89
Voltmeter DigitaI Blue 0-200V DC 0.56 Voltmeter DigitaI Blue 0-200V DC 0.56 features: - 3-wire recessed LED Voltmeter - No battery needed -Measuring range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Blue Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0045 Available Price €2.99
Digital Voltmeter Red 0-200V DC 0.56 Digital Voltmeter Red 0-200V DC 0.56 features: - No battery needed - Measurement range: 0-200 Vdc - Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Red Led - Color: Black - Includes reverse polarity protection - Operating current: Code M0047 Last items in stock Price €2.59