Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 Manufacturer: Taiwan Semiconductor 5x Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 features: - Type Output: fixed- Voltage Output: 3.3 V- Output Current: 800mA- Max input voltage: 12V- Operating temperature: -20C to + 85ºC- Encapsulated: SOT223- Dropout Voltage Vdo: 1.3V (1A)- Quantity: 5 units Code T0001 ✗ Out-of-Stock Price €0.75
Precision Temperature Sensor TO-92 LM335 LM335Z-ST Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:- Power supply from 5 to 30 Vdc- Connection through analog input- Temperature range from -40ºC to 100ºC- Linearity +10 mV / ºK- Accuracy of measurement: ± 2 ° C- Manufacturer: Texas Instruments Code S0120 Available Price €3.99
Ceramic Capacitor 470nF 50v 474 Ceramic Capacitor 470nF (0,1uF) 50v 104 PCB PIC Arduino features:-Type: ceramic Y5V-Tolerance: +80% -20%-Dimensions: diameter 9.5mm, pitch 5.08mm Code D0060 Available Price €0.07
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.39
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.79
L293D STM Module Expansion Board 2 Motors - 25V/0.6A The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V. Code M0108 Available Price €4.59
Flange Bearing F605ZZ Ball Bearing 3D Printer Reprap Prusa - Measurements: * Inner diameter D: 5mm * Outside diameter D: 14mm * Width - dimension B: 5mm * Dimension C1: 1mm * Dimension D1: 16mm - Quantity: 1 unit Code I0081 Available Price €0.85
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €7.90
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €17.90 -€1.41 Price €16.49
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Regular price €11.95 -€2.40 Price €9.55
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €6.90
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €8.95 -€3.00 Price €5.95
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Regular price €9.60 -€1.00 Price €8.60
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Available Price €16.90
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €6.99
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 Available Price €16.90
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €8.95 -€3.00 Price €5.95
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Regular price €11.95 -€2.40 Price €9.55
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €6.90
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €17.90 -€1.41 Price €16.49
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €7.90
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Regular price €9.60 -€1.00 Price €8.60
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €6.99