0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display
  • 0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display

0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display

P0134

0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display features:
- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degrees
- Screen color: blue and yellow (1/4 above yellow and 3/4 below blue)
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer, instruments, DIY projects, etc ...
- It is an OLED screen module with blue-yellow display and with a resolution dot matrix 128x64 and an IC2 interface.
- The display includes the driver controller SSD1306 128 x 64 Segment Driver / OLED / PLED Common.

OEM
Add to wish list

0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display features:

- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degrees
- Screen color: blue and yellow (1/4 above yellow and 3/4 below blue)
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer, instruments, DIY projects, etc ...
- It is an OLED screen module with blue-yellow display and with a resolution dot matrix 128x64 and an IC2 interface.
- The display includes the driver controller SSD1306 128 x 64 Segment Driver / OLED / PLED Common.
- Compared to LCD, OLED displays are much more competitive, They have a number of advantages such as high brightness, self-emission, high contrast ratio, angle of view. n wide, wide temperature range, and low power consumption.

Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: h2 >

Communicate with OLED 0.96 '' screen

- Connect OLED 0.96´´ screen with UNO module div >
Draw graphics on the OLED 0.96 '' screen

Write texts on the OLED 0.96 ''
< br />
- Application with a DHT22 / AM2302 temperature / humidity sensor

Data sheet

Interfaces
12C
Dimensions
0.96''

Customers who bought this product also bought

2x Female 40-Pin Long Strip

2x Female 40-Pin Long Strip features:
- Pin spacing: 2.54mm
- Pin length: 10.5mm
- Insert position: vertical - Insertion: through
- Quantity: 2 units of female strips of 40 pins each

K0085

Price €0.79

Sensor Module Moisture Earth Water Soil

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

S0021

Price €1.61

LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable

It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader.
The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features:
- ATmega32u4 microcontroller,
- Operating voltage 5V,
- Power (recommended) 7-12V,
- Digital pins I / O 20 (of which 7 can be used as PWM outputs),
- Analog input pins 12,
- DC current through I / O Pin 40 mA,
- DC current for pin 3.3V 50 mA,
- Flash memory 32 KB (of which 4 KB are used by the bootloader),
- SRAM 2.5 KB,
- EEPROM 1 KB, - Clock speed 16 MHz,
- Interface: UART, USB, SPI, I2C,
- USB communication - Atmega32u4,

B0004

Regular price €9.01 -€2.00 Price €7.01

Momentary Switch Push Button Red N/O 7mm

Momentary Switch Push Button Red N/O 7mm features:
- Momentary pushbutton N/O (normally open)
- Red button
- Dimensions approx. 7 mm x 27 mm
- Recessed with nut and washer
- Load current (supported): 1A to 230V / 2A to 125V
- Drill to embed: 7 mm +/- 0.2
- Operating temperature: -55º to +85ºC

K0156

Price €0.37

DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

I0012

Price €2.88

Display OLED 0.96" 128x64 White I2C 4 Pin

Display OLED 0.96" 128x64 White I2C 4 Pin features:
- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degree
- Screen color: white
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer , instruments, DIY projects, etc ...
- It is an OLED display module with white display and with a dot matrix of a resolution 128x64 and an IC2 interface.
- The display includes the IC driver SSD1306 128 x 64 OLED / PLED Segment / Common Driver.

P0091

Regular price €5.37 -€2.51 Price €2.86

Kapton type 10mm thermal tape

Characteristic: - Supports up to 280ºC
- Electrical and antistatic insulation
- Resistant to acid and alkaline products
- Resistant to solvent
- Adhesive
- Length Approx: 33m
- Polyamide adhesive tape 10mm 
- Known as Kapton polyamide tape
- Product for welding works on those that need to protect some component from the heat

I0061

Price €1.78

Rain Sensor Module Water Droplet Detector

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

S0022

Price €1.40

Related articles on blog

No related article on blog

€6.20
Save €1.00 €5.20

5,20 tax excl.

1
30+ items
Regular price €6.20 Price €5.20

Order until 4pm we will send today
30 days return