Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C
  • Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C
  • Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C
  • Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C
  • Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C

Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C

P0024

Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C features:
- Oled 0.96 "Display of 128 * 64 pixels
- one yellow line and 3 blue lines
- Drive IC model SDD1306
- Power supply: 3V-5.5V
- View angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption 0.08W
- Temperature usage: -20 to 70 ºC
- PCB board dimension: 32 x 32 mm
- OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption energy.
Applications: - Due to the size, quality and consumption of smart watch products, portable meters, medical devices, portable players, etc.

Waveshare
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Screen OLED 0.96" A 128x64 Yellow-Blue SPI/I2C features:

- Oled 0.96 "Display of 128 * 64 pixels
- one yellow line and 3 blue lines
- Drive IC model SDD1306
- Power supply: 3V-5.5V
- View angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption 0.08W
- Temperature usage: -20 to 70 ºC
- PCB board dimension: 32 x 32 mm
- OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption energy.
Applications:

- Due to the size, quality and consumption of smart watch products, portable meters, medical devices, portable players, etc.

Data sheet

Interfaces
I2C/SPI
Dimensions
0.96''

Customers who bought this product also bought

Battery LIPO 210mAh 3.7V

LITHIUM POLYMER BATTERY Battery LIPO 210mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 210 mAh. - Embedded PCM security chip (protection against overcharging, over discharge, short circuit) Dimensions: -Length / depth of battery- 25mm -Battery width / diameter- 31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

PP040

Price €3.13

Passive Buzzer 5V

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

M0196

Price €0.37

Mini vibration engine for Arduino and Raspberry Pi 5 VDC

This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor.
Mini vibration engine for Arduino and Raspberry Pi 5 VDC features:
- Voltage: 5 VDC,
- Current: 75mA,
- Rotation speed: 1100 (rpm),
- Efficiency: 80%,
- Dimensions: 10x27mm.

M0174

Price €0.83

MQ-3 Alcohol Sensor Module Ethanol Breathalyzer

Ethanol alcohol sensor module.
MQ gas sensor uses a small indoor heater with an electrochemical sensor.
When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:
- Main chip: alcohol sensor MQ-3 and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Detection concentration:
- 0.05mg/L - 10mg/L
- Quick response features:
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

S0009

Price €2.44

TDA7498 Class D 2X100W Amplifier

Characteristic: - Quiescent current: 50 mA (without load)
- Efficiency: 90%
- Nominal output power max.: 2 x 100W
- Frequency response: 20Hz to 20KHz
- Operating voltage: DC20V to DC34V
- Recommended supply voltage: DC32V
- Speaker parameters: 6 Ohm , 8 Ohm
- PCB board size: 87 × 72 mm
- Package includes cable

M0035

Price €16.12

LED 10-Segment Bar Graphics Display Red

LED 10-Segment Bar Graphics Display Red features:
- Bargraph LED display
- Number of segments: 10
- Size: 5mm - Dimensions: 25x10mm
- Material GaAsP / GaP
- Color: red
- Wavelength: 635 nm
- Vf / forward /2.1 V
- I fw / forward / 30 mA
- Iv / Ifw = 20mA / 4 mcd
- Number of terminals: 20

P0100

Price €0.93

Micro SD Card Reader/Recorder

The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.
The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.
Ideal for projects with ARDUINO, PIC, AVR, STM32.
Micro SD Card Reader/Recorder features:
- Supply voltage: 4.5V- 5.5V
- Adjustable 3.3V built-in regulator for SPI pins
- Consumption <200mA
- Interface: SPI
- Dimensions: 24mmx 42mm x 12mm
Supports microSD cards (up to 2G) and micro SDHC (up to 32G)

M0006

Price €2.06

Related articles on blog

No related article on blog

€6.44

6,44 tax excl.

Out of stock
Do you want to receive an alert when product is back in stock?
 
We will send you an email once the product becomes available. Your email address will not be shared with anyone else.
Price €6.44

Order until 4pm we will send today
30 days return