Potentiometer B50K linear Potentiometer B50K linear features: -50k OHM kΩ - linear potentiometer 50k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0069 Available Price €0.99
Electronic waterproof plastic cover IP65 waterproof case ideal for electronic projects, energy supplies, student projects, amplifiers. Electronic waterproof plastic cover features: - Material: extruded plastic,- Waterproof protective indication: IP65,- Includes 4 screws and waterproof assembly,- Size external: 158x90x60mm, - Dimension internal: 158x90x60mm, - Weight: approx. 190g Code H0153 Available Regular price €5.99 -€1.00 Price €4.99
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.69 -€0.20 Price €2.49
WS2812 RGB 5050 Smart Addressable 5V Arduino compatible LED WS2811 WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features: - WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually - WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable. - They are based on the 5050 LED - 24-bit color control (8-bit PWM per channel) - 16.8 millions of colors per LED - One-wire communication - Power: max. 5 Vdc - Current: 18.5mA - Input and output terminals (data and power) Code P0102 Available Price €1.69
LED Diode Assortment Kit 30 pcs 5mm red, green, yellow LED Diode Assortment Kit 30 pcs 5mm red, green, yellow features:- Lens color: red, green, yellow - diffuse- Size: 5mm- Operating current: 20mA- Voltage (red) 1,8V-2,3V- Voltage (green) 3,2V-3,4V- Voltage (yellow) 1,8V-2,3V- Anode (A): Positive (long leg): 28mm- Catode (K): Negative (short leg): 25mm - Operating temperature: -25ºC/80ºC- Welding temperature: +260ºC - Quantity: 30 units*10x red*10x green*10x yellow Code P0011 Available Price €0.06
20x4 2004 LCD display PCF8574T I2C Backlit Blue - It consists of a 20-character, 4-row display - The display is compatible with the controller HD44780 and integrates the module so you can use it through the I2C protocol without any problem - Only two pins are needed for communication, SDA and SCL - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - It can be changed to any between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 20x4 2004 LCD display PCF8574T I2C Backlit Blue features: - LCD screen, 20 characters and 4 lines - 5V power supply - HD44780 compatible controller Code P0013 Available Regular price €8.49 -€1.50 Price €6.99
Battery holder 2x 18650 PCB mount Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm - Weight: 10 gr . (approx.) - Stack length max 67mm Code PP052 Available Regular price €2.49 -€0.40 Price €2.09
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €9.49
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €2.39
Sonoff T0EU1C-TX Gang 86 Smart WiFi Wall Touch Switch WiFi Smart Wall Switch Sonoff T1 Gang 86 Smart WiFi RF APP Touch Control Wall Light Switch features:works with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone Android. Code W0089 Available Regular price €19.90 -€1.91 Price €17.99
SONOFF 5050RGB - LED strip light IP65 2M 2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included) Code WS061 Available Regular price €10.95 -€2.00 Price €8.95
6 V Peristaltic Submersible Mini Pump Small peristaltic pump is a type of hydraulic positive displacement pump used for pumping a variety of fluids. Code M0229 Available Price €16.79
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 Available Price €9.45
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €9.49
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €2.39
Sonoff T0EU1C-TX Gang 86 Smart WiFi Wall Touch Switch WiFi Smart Wall Switch Sonoff T1 Gang 86 Smart WiFi RF APP Touch Control Wall Light Switch features:works with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone Android. Code W0089 Available Regular price €19.90 -€1.91 Price €17.99
SONOFF 5050RGB - LED strip light IP65 2M 2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included) Code WS061 Available Regular price €10.95 -€2.00 Price €8.95
6 V Peristaltic Submersible Mini Pump Small peristaltic pump is a type of hydraulic positive displacement pump used for pumping a variety of fluids. Code M0229 Available Price €16.79
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 Available Price €9.45