Motor controllers

TB6612FNG controller, double H-bridge controller driver.
Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32.
An improved version of the L298N.
H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N.
The TB6612FNG has better efficiency and smaller dimensions than the L298N.
Controller TB6612FNG DC PAP motor features:

- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 13.5 V (15V max)
- Maximum current: ± 3A per channel (1.2 A direct current per channel)
- Logic voltage: 5V

It allows controlling many different types of engines: - Up to 4 bidirectional current motors
- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos.                   L293D Motor Drive Shield Expansion Board features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A (650mA)
- Logic voltage: 5V
- Controller L293D
- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.
Pull-down resistors keep the motors off during startup.

Mosfet 24V 5A IRF520 PWM controller features:
- The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater.
- The built-in IRF520 N-MOSFET transistor
- Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI)
- Charging voltage: 0-24V
- Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point)
- 60W max power (more than 10W must be equipped with a heat sink)
- Terminalblock connectors
- LED indicating the presence of power
- Dimensions: 33x24mm

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

Driver capable of handling up to two high consumption motors.
We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables.

The module for DIY Arduino hobby
Motor driver L9110 for Arduino, Smart Car, Robotics
Small magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features:
- Operating voltage: 5V
- PCB dimension: 3.5 x 2.6cm
- Double red propeller
- Blade length 75mm
- Weight: 6 g
- Quantity:
  1x DC motor
  1x double helix

LSC-16 Digital Servo Motor Controller 16 channels features:
- With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU.
- CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed.
- 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions!
- Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically).
- 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor.

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It incorporates a switch for the connection and disconnection of the entire module.
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth />

A3967 controller, double H-bridge controller driver.
Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features:

- Minimum operating voltage: 7.00 V
- Voltage maximum operating: 30 V

The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased.

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice.