Arduino

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased.

This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person.

Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid.

This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together.

MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V.

This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads.

This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds

This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person.

SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project.

2 Channel Relay Module 5V 10A for Arduino features:
- 5V relay module with 2 optocoupled channels
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- LED indicator: For each channel
- Dimensions: 40x 50mm

Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features:
- Interface type: USB
- Supports IEEE 802.11e draft 802.11n
- Supports USB 2.0, compatible with USB 1.1 and 1.2
- Support systems:
- Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux
- Operating distance: 91 meters indoors, 275 meters in open space
- Transfer rate: 150Mbps (downlink) and 150Mbps (uplink)
- Works with old Wireless-G and Wireless-B networks
- WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM
- Frequency range: 2.4 to 2.4835 GHz
- Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment
- Transmission mode: DSSS

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino

This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

It is a version without headers of a popular BOB-09868 from SparkFun.

In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005).

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors

This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module  is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use.

This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor.
Mini vibration engine for Arduino and Raspberry Pi 5 VDC features:
- Voltage: 5 VDC,
- Current: 75mA,
- Rotation speed: 1100 (rpm),
- Efficiency: 80%,
- Dimensions: 10x27mm.

The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements.

HD V2 Raspberry Pi camera board The Raspberry Pi High Definition (HD) camera board connects to any Raspberry Pi or Compute Module to create HD photos and video.
Uses Sony's IMX219PQ image sensor that offers high-speed, high-speed video images Sensitivity.
Raspberry Pi Camera Module offers reduced image contamination such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection.
Raspberry Pi Camera Board, Sony IMX219 8 Megapixel Sensor features:
High-quality images
High data capacity
Fixed 8 megapixel focus (includes focus adjustment tool)
Compatible with 1080p, 720p60 and VGA90
Sony IMX219PQ CMOS image sensor
15-pin ribbon cable

Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark.
The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images.
The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features:
and benefits: No infrared filter
High quality images

Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies.

SparkFun Hamburger speaker is a high quality speaker in a small form and with even smaller price. You wouldn't believe you can get a quality product for less than 7€, right? Well, we couldn't believe that as well, but SparkFun makes that possible.

This small GPS breakout is yet another Qwiic module from SparkFun as per usual based on I2C - meaning that you can keep your serial port free for other applications. The board features XA1110 GPS module from GTOP and MediaTek MT3333 chipset already loaded with SparkFun firmware enabling clean and easy use of both ports. 

It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328.

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV.

Impressive, professional, high-definition camera module. Official product of Raspberry Pi.

The official Raspberry Pi HQ Camera includes a 1/3" (8.5mm) Sony IMX477 sensor with 12.3MPx resolution and up to 50% increased sensitivity of pixels per area, offering greater sensitivity to light.

It is specially designed to work with CS or C-mount interchangeable lenses (CS-C adapter included). It allows you to use both fixed and varifocal lenses, and you can also use other lenses such as M12 lenses by using an M12 to CS mount converter.

16mm fixed lens compatible with Raspberry Pi official HQ Camera (Reference RA094) C-mount, long distance telephoto type (up to 40m) 10 Mpx.