MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
PCB Heated Bed MK3 Alu 3mm 12V 24V 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Available Price €11.99
LED 1W Pink SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 3.2-3.4V - Current: 350mA - Luminous flux: 100-110LM - Ã beam angle: 140 degrees - Color emission: pink Code P0161 Available Price €0.85
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
30x 1N4007 Rectifier Diodes 1A 1000V DO-41 1N4007 Rectifier Diodes 1A 1000V DO-41 features:- Standard rectifier diode- Configuration: Simple- Reverse voltage: 1000V- Direct voltage drop: 1V- Direct direct current: 1A- Maximum overvoltage current: 30A- Encapsulated: DO-41- Operational tension: -65ºC to + 125ºC- Quantity: 30 units Code T0002 Available Price €0.05
Blue cleaning sponge for soldering iron tip with pre-cut circle at the center Blue sponge to clean the tip of your soldering iron to the tin. Blue cleaning sponge for soldering iron tip with pre-cut circle at the center features: - Circle diameter 17mm precut to the center of the sponge,- Size: 55x55mm,- Material: sponge,- Color: blue,- Quantity: 1. Code H0151 Available Price €0.80
Solar panel DIY 6V 1W Solar panel DIY 6V 1W features: - Mobile DIY Solar System Photovoltaic Charger Cell - Working voltage: 6V - Output power: 1W - Working current: 0-200 mA - Product size: 110x60x3 mm Code A0062 Available Price €3.95
Tin Roll 60/40 Sn/Pb 2.5% Flux 10g 1mm Tin ideal for application in consumer electronics circuitsTin Roll 60/40 Sn/Pb 2.5% Flux 10g 1mm features:- 10 gr. welding wire of 1 mm diameter. 60% tin, 40% lead- Melting temperature 187/190 C- Alloy Sn60Pb40- Flux 2.5% SW26 1.1.2B ISO9454 - It is leaded alloy for manual and automatic processes where meeting the requirements of the RoHS2 Directive is not required. - Quantity: 1 unit- High quality - manufactured in EU Code Q0004 Available Price €1.49
Welding Wire 1kg Tin 60/40 Sn/Pb Lead 2.5% Flux 1.0mm Tin ideal for application in consumer electronics circuits. Welding Wire 1kg Tin 60/40 Sn/Pb Lead 2.5% Flux 1.0mm. 60% tin and 40% lead. Melting temperature 183 o C / 190 o C. Flux 2.5%Manufactured in EU Code Q0144 Last items in stock Price €65.90
Desoldering Wire 1mm 1.0 High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 1mm 1.0 features:- Material: Copper- Length: 1.5m- Width: 1.0mm- Desoldering Braid Solder Remover Wick 1mm / 1.5m- Pure copper braid construction- Quick removal welding- Excellent thermal for a faster and safer desoldering Code H0003 Available Price €1.79
Welding Wire Tin Sn60Pb40 Lead 1.2% Flux 0.6mm 50g Welding Wire 50g Tin 60/40 Sn/Pb Lead 1.2% Flux 0.6mm features: - 50gr. 0.3mm diameter welding wire. 60% tin and 40% lead - Fusing temperature 183 „ƒ / 190 „ƒ - Alloy Sn60 Pb40 - Flux 1.2% - Quantity: 1 unit Code Q0125 ✗ Out-of-Stock Price €3.49
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 0.5mm 250g Tin ideal for application in consumer electronics circuits. Welding Wire 250g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm. Code Q0111 ✗ Out-of-Stock Price €19.95
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm Tin ideal for application in consumer electronics circuitsWelding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm features:- 100gr. 0,5mm diameter welding wire. 60% tin and 40% lead- Melting temperature 183 o C / 190 o C- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0005 Available Price €8.95
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 0.25mm 100g Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.25mm features: - 100gr. 0.25mm diameter welding wire. 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0107 Last items in stock Price €16.49
Tin dispenser for solder reel Solder dispenser for convenient and faster soldering. Easily supplies you with solder in a fixed structure. Code H0187 Available Price €4.99
Desoldering Wire 2.5mm High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 2.5mm features:- Material: Copper- Length: 1.5m- Width: 2.5mm Code H0007 Available Price €1.79
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm Tin ideal for application in consumer electronics circuits.Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm features:- 100gr. 1.2mm diameter welding wire- 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0003 ✗ Out-of-Stock Price €8.95
Tin Roll 60/40 Sn/Pb 2.5% Flux 10g 1mm Tin ideal for application in consumer electronics circuitsTin Roll 60/40 Sn/Pb 2.5% Flux 10g 1mm features:- 10 gr. welding wire of 1 mm diameter. 60% tin, 40% lead- Melting temperature 187/190 C- Alloy Sn60Pb40- Flux 2.5% SW26 1.1.2B ISO9454 - It is leaded alloy for manual and automatic processes where meeting the requirements of the RoHS2 Directive is not required. - Quantity: 1 unit- High quality - manufactured in EU Code Q0004 Available Price €1.49
Welding Wire 1kg Tin 60/40 Sn/Pb Lead 2.5% Flux 1.0mm Tin ideal for application in consumer electronics circuits. Welding Wire 1kg Tin 60/40 Sn/Pb Lead 2.5% Flux 1.0mm. 60% tin and 40% lead. Melting temperature 183 o C / 190 o C. Flux 2.5%Manufactured in EU Code Q0144 Last items in stock Price €65.90
Desoldering Wire 1mm 1.0 High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 1mm 1.0 features:- Material: Copper- Length: 1.5m- Width: 1.0mm- Desoldering Braid Solder Remover Wick 1mm / 1.5m- Pure copper braid construction- Quick removal welding- Excellent thermal for a faster and safer desoldering Code H0003 Available Price €1.79
Welding Wire Tin Sn60Pb40 Lead 1.2% Flux 0.6mm 50g Welding Wire 50g Tin 60/40 Sn/Pb Lead 1.2% Flux 0.6mm features: - 50gr. 0.3mm diameter welding wire. 60% tin and 40% lead - Fusing temperature 183 „ƒ / 190 „ƒ - Alloy Sn60 Pb40 - Flux 1.2% - Quantity: 1 unit Code Q0125 ✗ Out-of-Stock Price €3.49
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 0.5mm 250g Tin ideal for application in consumer electronics circuits. Welding Wire 250g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm. Code Q0111 ✗ Out-of-Stock Price €19.95
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm Tin ideal for application in consumer electronics circuitsWelding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm features:- 100gr. 0,5mm diameter welding wire. 60% tin and 40% lead- Melting temperature 183 o C / 190 o C- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0005 Available Price €8.95
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 0.25mm 100g Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.25mm features: - 100gr. 0.25mm diameter welding wire. 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0107 Last items in stock Price €16.49
Tin dispenser for solder reel Solder dispenser for convenient and faster soldering. Easily supplies you with solder in a fixed structure. Code H0187 Available Price €4.99
Desoldering Wire 2.5mm High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 2.5mm features:- Material: Copper- Length: 1.5m- Width: 2.5mm Code H0007 Available Price €1.79
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm Tin ideal for application in consumer electronics circuits.Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm features:- 100gr. 1.2mm diameter welding wire- 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0003 ✗ Out-of-Stock Price €8.95