DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 ✗ Out-of-Stock Price €2.06
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.06
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 Available Price €14.83
40x Male to male cables 20cm Characteristic: -Length: 20cm -Quantity: 40 cables -Mono Dupont connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0006 Available Price €2.06
Mini Submersible Water Pump DC 3V 120L/H Characteristic: - Operating voltage: 3-6V - Max flow: 80-120 l / h - Maximum pumping height: 40-110cm - Continuous working time of 500 hours - Cable length: 20cm - Inside outlet diameter: 5 mm - Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm Code M0040 Available Regular price €2.06 -€0.51 Price €1.55
40x Cables Female-Male 20cm 40x Cables Female-Male 20cm features: -Length: 20cm-Quantity: 40 cables-Connectors have male and female header contacts at either end-Compatible with female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0008 Available Price €2.06
Hantek 20:1 attenuator - suitable for passive signal attenuation of a 1008C HT201 20:1 oscilloscope 300V Max This attenuator allows the oscilloscope to measure the fuel injector and primary ignition waveforms. Passive attenuator with a 20:1 attenuation Therefore, if a 20V signal is introduced, it will emit a 1V signal. Using this element, the oscilloscope can measure voltage higher than its range (*20V) Code H0211 Available Price €9.08
Servo with Rotation 180 Servo Motor Type S3003 Servo with Rotation 180 Servo Motor Type S3003 features: - Model Aircraft Futaba Arduino Robotics - Operating Voltage: 4.8V to 6V - Max Torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degrees (4.8V), 0.19sec / 60 degrees (6V) - Max radius: 180º - Temperature range: -20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese manufacturing Code R0018 Available Regular price €5.20 -€0.30 Price €4.90
Hantek CC-650 BNC Clamp (650A) This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed. Code H0241 Last items in stock Price €89.17
Compact Digital non-contact laser tachometer RPM DT2234C+ Compact instrument that measures the speed of rotation with a visible red light beam from a powerful LED. The high intensity class II laser measures wide measurement range and high resolution, from 2.5 to 99.999 RPM (Revolutions per Minute) Code H0193 Available Regular price €11.98 -€2.00 Price €9.98
Wind meter with temperature measurement function Uni-T UT363S UT363S mini wind speed and temperature meters. UT363S measures wind speeds up to 30 m/s (108 km/h) with an accuracy of 0.01. The following units of measurement are available: m/s, km/h, ft/min, knots, mph. Code H0360 Last items in stock Price €40.90
FDY10-S Battery Tester, Charge and Discharge Time Meter FDY10-S is a new measuring device with integrated double function, detection and measurement.During discharge, the LED shows the voltage, the current, the power in real time. After completing the battery discharge, it will display the results of the measurement, such as the download time.The host and the heating elements are separated, high stability.The measurement error is minimal and the most accurate results are due to the application of the measurement mode of the 4-wire system.Availability to configure the automatic slide show function to verify visually and clearly the operating states and parameters, due to the display mode based on the combination of the LED indicator light.Operation sound indication and alarm for the end of the discharge. Code H0140 ✗ Out-of-Stock Regular price €54.50 -€10.00 Price €44.50
Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer features: - Uni-T M890C + Digital Multimeter LCD AC DC Voltmeter Ammeter- Power supply: 9V battery- Protection: F 250mA / 250V- Display: LCD, range up to 1999 update: 2-3/s- Method: double A / C slope- Indication of exceeding the range: on the screen only by the number "1"- Polarization of traffic for negative visualization "-"- Operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F)- Storage temperature: -10 °C ~ 50 °C (10 °F ~ 122 °F)- Flat battery signal: the screen shows "BAT"- Dimensions: 170x87x35 mm- Weight: 215g- Sound traffic: YES (piezo) Specifications: - DCV: 200m-2-20-200-1000V ± 0.5%- ACV: 2-20-200-750V ± 1.0% Code H0059 ✗ Out-of-Stock Price €17.27
non-contact basic voltage detector - Fazer 767 Test pen for non-contact voltage detection. It can detect AC current up to 500V and DC current up to 60V. This detector complies with IEC61010 standards: pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation. Code H0315 Last items in stock Price €2.88
Power socket tester with RCD test function Uni-T UT07B-EU The UT-07B-EU tester indicates the correct connection of L, N, PE cables in a socket. It also has a function to check the efficiency of residual current devices (RCD). The device is made of resistant plastic, which is very useful during installation work and ensures long-lasting correct operation. Attention! The RCD check is only possible if the phase is on the right-hand side. Code H0564 Available Price €12.36
Power supply 30V 5A UNI-T UTP3315TFL Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A. The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features: - Input voltage: 230VAC - Output voltage: 0-30V adjustable - Output current: 0-5A adjustable - Backlit display - Protection against over-consumption and short circuit - Cooled by fan - Includes crocodile clip cables Uni-T UTP3315TFL datasheet Load Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.2% + 3mA Line Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.1% + 5mA Ripple and Noise Voltage 1mV rms Current 3mA rms Code H0181 Last items in stock Price €98.76
Non-contact temperature measuring thermometer Uni-T UT300H The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc. Code H0313 Last items in stock Regular price €28.51 -€4.55 Price €23.96
Hantek CC-65 BNC Clamp (65A) This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed. Code H0240 Last items in stock Regular price €75.95 -€2.00 Price €73.95
Hantek CC-650 BNC Clamp (650A) This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed. Code H0241 Last items in stock Price €89.17
Compact Digital non-contact laser tachometer RPM DT2234C+ Compact instrument that measures the speed of rotation with a visible red light beam from a powerful LED. The high intensity class II laser measures wide measurement range and high resolution, from 2.5 to 99.999 RPM (Revolutions per Minute) Code H0193 Available Regular price €11.98 -€2.00 Price €9.98
Wind meter with temperature measurement function Uni-T UT363S UT363S mini wind speed and temperature meters. UT363S measures wind speeds up to 30 m/s (108 km/h) with an accuracy of 0.01. The following units of measurement are available: m/s, km/h, ft/min, knots, mph. Code H0360 Last items in stock Price €40.90
FDY10-S Battery Tester, Charge and Discharge Time Meter FDY10-S is a new measuring device with integrated double function, detection and measurement.During discharge, the LED shows the voltage, the current, the power in real time. After completing the battery discharge, it will display the results of the measurement, such as the download time.The host and the heating elements are separated, high stability.The measurement error is minimal and the most accurate results are due to the application of the measurement mode of the 4-wire system.Availability to configure the automatic slide show function to verify visually and clearly the operating states and parameters, due to the display mode based on the combination of the LED indicator light.Operation sound indication and alarm for the end of the discharge. Code H0140 ✗ Out-of-Stock Regular price €54.50 -€10.00 Price €44.50
Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer features: - Uni-T M890C + Digital Multimeter LCD AC DC Voltmeter Ammeter- Power supply: 9V battery- Protection: F 250mA / 250V- Display: LCD, range up to 1999 update: 2-3/s- Method: double A / C slope- Indication of exceeding the range: on the screen only by the number "1"- Polarization of traffic for negative visualization "-"- Operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F)- Storage temperature: -10 °C ~ 50 °C (10 °F ~ 122 °F)- Flat battery signal: the screen shows "BAT"- Dimensions: 170x87x35 mm- Weight: 215g- Sound traffic: YES (piezo) Specifications: - DCV: 200m-2-20-200-1000V ± 0.5%- ACV: 2-20-200-750V ± 1.0% Code H0059 ✗ Out-of-Stock Price €17.27
non-contact basic voltage detector - Fazer 767 Test pen for non-contact voltage detection. It can detect AC current up to 500V and DC current up to 60V. This detector complies with IEC61010 standards: pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation. Code H0315 Last items in stock Price €2.88
Power socket tester with RCD test function Uni-T UT07B-EU The UT-07B-EU tester indicates the correct connection of L, N, PE cables in a socket. It also has a function to check the efficiency of residual current devices (RCD). The device is made of resistant plastic, which is very useful during installation work and ensures long-lasting correct operation. Attention! The RCD check is only possible if the phase is on the right-hand side. Code H0564 Available Price €12.36
Power supply 30V 5A UNI-T UTP3315TFL Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A. The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features: - Input voltage: 230VAC - Output voltage: 0-30V adjustable - Output current: 0-5A adjustable - Backlit display - Protection against over-consumption and short circuit - Cooled by fan - Includes crocodile clip cables Uni-T UTP3315TFL datasheet Load Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.2% + 3mA Line Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.1% + 5mA Ripple and Noise Voltage 1mV rms Current 3mA rms Code H0181 Last items in stock Price €98.76
Non-contact temperature measuring thermometer Uni-T UT300H The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc. Code H0313 Last items in stock Regular price €28.51 -€4.55 Price €23.96
Hantek CC-65 BNC Clamp (65A) This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed. Code H0240 Last items in stock Regular price €75.95 -€2.00 Price €73.95