Power supply 30V 5A Zhaoxin RXN-305D

The LM570R-I laser spirit level is a handy tool used in the construction industry for horizontal and vertical levelling. The 10mW red laser is ideal for projects requiring accurate levelling in a two-dimensional area.

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms

UT100 series is specially designed for automobile diagnosis. Combines RPM, DWELL, and other multimeter functions. The series is useful for car maintenance personnel to diagnose traditional vehicles and hybrid electric vehicles. Applications: Its applications include working on fuses, switches, solenoids, relays, charging systems, fuel systems, engine detection, etc.

The voltage / power / battery level indicator KA2284 contains five LED lights that light up progressively as the voltage increases, from green to red to yellow.
It is ideal for your projects that require voltage level indicators, such as battery capacity and audio level indicators.
The built-in potentiometer adjusts the range (sensitivity) of the LED display, and the DC or AC input can be selected via the P2 bridge.
The AC and DC input can be controlled with bridge P2: bypassed for DC, open for AC.
Adjustable power level through the potentiometer. Power Level KA2284 Indicator Module 5 LED features:
- Operating voltage: 3.5 - 12 VDC
- 5 level LED KA2284 controller
- Adjustable power
- 4 pin terminal:
       - IN: Input voltage to measure

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

DDS UNI-T UTG932E 2-channel signal generator can generate sine wave, square wave, triangle wave, pulse wave and arbitrary wave, etc. The maximum output frequency of sine wave is 30MHz, sampling rate of 200 MSa/s.

Modern digital multimeter with large LCD display that provides a better user experience. Voltage / current / resistance analysis, as well as diode, transistor and continuity tests.

This multimeter complies with IEC61010 standards: in pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.

This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed.

Modern digital multimeter with large 4 digits LCD display that provides a better user experience. Voltage / current / resistance / capacitance / frecunecy analysis, as well as diode, transistor and continuity tests. Max. display 19999  4 ½ digits

This multimeter complies with IEC61010 standards: in pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.

The device is designed to find and identify cables without disturbing the insulation. Finds broken wires, fault points and continuity test.