Digital Multimeter Uni-T UT39A+

The voltage / power / battery level indicator KA2284 contains five LED lights that light up progressively as the voltage increases, from green to red to yellow.
It is ideal for your projects that require voltage level indicators, such as battery capacity and audio level indicators.
The built-in potentiometer adjusts the range (sensitivity) of the LED display, and the DC or AC input can be selected via the P2 bridge.
The AC and DC input can be controlled with bridge P2: bypassed for DC, open for AC.
Adjustable power level through the potentiometer. Power Level KA2284 Indicator Module 5 LED features:
- Operating voltage: 3.5 - 12 VDC
- 5 level LED KA2284 controller
- Adjustable power
- 4 pin terminal:
       - IN: Input voltage to measure

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms

With the logic signal state tester it is possible to detect 0, 1, high impedance states. The indication reading is displayed by means of LEDs. The supply voltage is 5-15V.

8-channel oscilloscope for vehicle testing.
More than 80 kinds of automotive diagnostic functions (ignition detection / sensor / bus detection / performance / starting and charging circuits , etc.). The video help function provides the diagnostic video help that can be viewed online. The diagnostic result can be generated a diagnostic report, printed or taken a screenshot by pressing a key, many methods to save the data. Supported for recording waveform for a long time. You can simulate the camshaft and crankshaft signal. Transmit signals through the USB 2.0 plug and play interface, and requires no additional power supply; Key Hantek 1008C PC Oscilloscope USB 8 Channel Automotive Diagnostic DAQ features:

UNI-T UTD2102CL+ Dual Channels Digital Storage Osciloscopio con 100MHz, 500MSa/s, 5000 wfms/s

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer features:
- Uni-T M890C + Digital Multimeter LCD AC DC Voltmeter Ammeter
- Power supply: 9V battery
- Protection: F 250mA / 250V
- Display: LCD, range up to 1999 update: 2-3/s
- Method: double A / C slope
- Indication of exceeding the range: on the screen only by the number "1"
- Polarization of traffic for negative visualization "-"
- Operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F)
- Storage temperature: -10 °C ~ 50 °C (10 °F ~ 122 °F)
- Flat battery signal: the screen shows "BAT"
- Dimensions: 170x87x35 mm
- Weight: 215g
- Sound traffic: YES (piezo) Specifications: - DCV: 200m-2-20-200-1000V ± 0.5%
- ACV: 2-20-200-750V ± 1.0%

This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed.

The UT333S is a digital temperature and humidity meter with stable, safe and reliable performance in a split design. The split design is ideal for monitoring small and difficult to access air ducts. Measure temperature and humidity in real time with the best UNIT technology!

The digital clamp meters are designed according to EN61010-2010 CAT II 600V/CAT III 300V, with overload protection, high reliability, high safety and high accuracy. These meters can be used to measure high voltage frequency, AC/DC current, etc.