Heated Bed PCB MK2B 3D Reprap Printer
  • Heated Bed PCB MK2B 3D Reprap Printer
  • Heated Bed PCB MK2B 3D Reprap Printer
  • Heated Bed PCB MK2B 3D Reprap Printer

Heated Bed PCB MK2B 3D Reprap Printer

I0001

Heated Bed PCB MK2B 3D Reprap Printer features:
- Measurements: 214mm x 214mm

OEM
Add to wish list

Heated Bed PCB MK2B 3D Reprap Printer features:

  • Measurements: 214mm x 214mm

Customers who bought this product also bought

Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.

S0025

Price €1.53

CP2102 USB 2.0 A RS232 Converter UART TTL Serial

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

C0001

Price €3.06

A3967 DC Motor PAP Driver Stepper - Easy driver

A3967 controller, double H-bridge controller driver.
Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features:

- Minimum operating voltage: 7.00 V
- Voltage maximum operating: 30 V

R0049

Price €2.44

E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car

Ideal for projects with ARDUINO, Smart Car
Detects transparent and translucent obstacles
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:
- Current consumption: up to 100 mA
- Supply voltage 5V
- Current consumption <25mA
- Response time of 2 ms
- Measured distance: 3-80cm 15st angle
- Screw to adjust the sensitivity, the back
- Output status led indicator
- Operating temperature: -25°C - + 55°C
- Material: high-strength plastic
- Type of output: normally open, NPN
- Dimensions: 18 mm in diameter, Length 45 mm
- Cable length 55cm
- Departures:
      - Brown: +
      - Blue: -
      - Black: OUT

S0004

Price €5.74

XL6009 DC-DC Step-Up Booster Controller LM2577

- The XL6009 module has a superior performance than the LM2577 module
- The regulator-booster of High performance
Characteristic:
- Based on the XL6009E1 regulator
- Input voltage: 3V-32V,
- Output voltage: 5-35V (adjustable),
- Output current: 2A maximum 3A (heat sink is required)
- Conversion efficiency: up to 94%
- Rectifier: not synchronous rectification
- Short circuit protection: current limitation, since recovery
- Operating temperature: industrial grade (-40 ° C - 85 ° C)
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Size: 50 x 22 x 15 mm

A0005

Price €2.02

Micro Servo 9g SG90

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

R0013

Regular price €2.22 -€0.20 Price €2.02

NTC thermistor 100K 3950 1m RepRap cable

Sensor used to measure the temperature of the hotend or hot bed of your 3D printer
Characteristic:
- NTC Thermistor 100 K 3950
- Impedance: 100 K (25º of Temperature)
- Accuracy: 1%
- Sensor Diameter: 1.8 mm
- Cable Length: 1 m
- Cable: AWM UL 3398 150 ° C 300V
- Ready to be installed and used. Fully insulated
- Designed to withstand the high temperatures of extrusion of plastics such as PLA and ABS

I0018

Price €0.91
€6.91
Save €2.00 €4.91

4,91 tax excl.

1
Last 3 items
Regular price €6.91 Price €4.91

Order until 4pm we will send today
30 days return