PCB Round Heated Bed 200mm MK2Y 3D Reprap Printer

Descripción: Light sensor module to measure light intensity and obtain digital data from it.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features:
- Chip BH1750FVI
- Supply voltage 3V-5V
- Integrated 16bit AD converter
- Detection range: 0-65535 lx (with an accuracy of 1 lux)
- Interface: II2C
- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)
- Dimensions 18.4 x 14 mm

This BLtouch sensor is an automatic leveling sensor for 3D printers that can accurately measure the inclination of your printing surface.
It can greatly improve the printing precision of your 3D printer.
Its features: are simple, smart and precise.
It could work with almost any type of bedding, such as glass, wood , metals, etc. 3DTouch's main functions and controls are the same as most automatic bed leveling sensors, consisting of an RC servo and a micro switch.

Self-leveling sensor BLtouch 3D printer features:
- Supply voltage: 5V.
- Supply current: 15mA
- Max. Current: 300mA
- Len3Dh cable: 150mm
- Wiring:
- 3 pins: Brown (-, GND) Red (+ 5V) Orange (control signal)

Fan 12V 2x Cable 50x50x15 3D Printer Reprap features:
- Voltage: 12V
- Speed: 7000rpm ± 10%
- Screw diameter: 4.5mm
- Time lifespan: 50,000 hours
- Operating temperature: -10 ° C to 70 ° C
- Cable length: 28cm
- Dimensions: 50mm x 50mm x 10mm

Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features:
- CH340 controller
- Supported OS: Win XP, Vista, Win 7.8, OS, Linux
- Work with Modbus, Profibus
- USB 2.0 specification with 6Mbps of maximum speed
- Measures: 60x 18x 14 mm

DC 10A Analog Panel Ammeter 0 to 10A features:
- DC 10A Ammeter Instrument Analog Amperage meter panel with shunt
- Type: Analogue ammeter
- Range: DC 0-10A
- Accuracy: class 2.5
- Size: 82mm fi
- Complete with screws for simple DIY installation
- This meter has a built-in bypass, does not need external derivation

A4988 + RepRap Radiator features:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge.

Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.
Provides seconds, minutes, time and date, calendar up to the year 2100.
DS1302 Real Time Clock RTC Module AVR ARM PIC features:
- Chip: DS1302
- Power supply: 2V-5V
- Operating current: <2mA
- Dimensions: 44 x23 x 8mm
- Battery not included in this sale
- Connect the RTC to your Arduino
VCC -> Arduino + 3.3V
GND -> Arduino Gnd
CLK -> (SCLK_PIN)
DAT -> (IO_PIN)
RST -> (CE_PIN)