Heat Shrinkable Tube 5 Colors 3 Meters Package Heat Shrinkable Tube 5 Colors 3 Meters Package features: - Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas. - These heat shrink tubes are very flexible and of high quality. Made in EU - Different sizes of 20 cm each are delivered: * 1,6mm: black, brown, red, yellow, orange * 2,4mm: black, brown , red, yellow, blue * 3,2mm: black, brown, red, yellow, blue - Quantity: 15 units - Material: polyolefin - Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter) - Minimum shrinkage temperature: 115 ° C maximum 200 ° C Code K0047 Available Price €1.95
PC6-01 Pneumatic connector for PTFE tube quick coupler Bowden connector - a pneumatic connector with a 9.7mm screw and 1.75 cm length for the 6mm tube of 3D printer couplers for 1.75mm filament. Code I0071 Available Price €1.79
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 ✗ Out-of-Stock Price €1.95
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €9.90
4x Springs Leveling Hot Bed 3D Printer 4x Springs Leveling Hot Bed 3D Printer features: 3D Springs printer Bed level extruder for RepRap Prusa Mendel - A strong spring for 3D Printer Extruder- Excellent elasticity, resistance to fatigue- Nickel plating, corrosion resistance, high hardness- Material: Carbon steel- Outside diameter: 7.5mm- Inner diameter: 5 mm- Spring height: 20 mm- Quantity of the ring: 9 rings- Surface treatment: Nickel-plating Code I0049 Available Price €0.39
Fan 12V 2x 3D Printer Cables Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 65mA - Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10% - Screw diameter: 4.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 11cm - Dimensions: 40mm x 40mm x 10mm Code I0026 Available Price €1.59
Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap features: - Number of teeth: 20 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 16mm - Inner hole: 8mm - Use with strap: 6mm and 6.35mm - Toothed width 7mm - Quantity: 1 unit - Ideal for fixing on the axis of the motors of your 3D printer Code I0063 Available Price €1.95
NTC thermistor 100K 3950 1m RepRap cable Sensor used to measure the temperature of the hotend or hot bed of your 3D printer Characteristic: - NTC Thermistor 100 K 3950 - Impedance: 100 K (25º of Temperature) - Accuracy: 1% - Sensor Diameter: 1.8 mm - Cable Length: 1 m - Cable: AWM UL 3398 150 ° C 300V - Ready to be installed and used. Fully insulated - Designed to withstand the high temperatures of extrusion of plastics such as PLA and ABS Code I0018 Available Price €1.10
PCB Round Heated Bed 200mm MK2Y 3D Reprap Printer Hot bed MK2Y powered by 12V current with a power of 90W. The maximum recommended temperature of the hot bed is between 110° - 135°, which is sufficient for ABS (at 110°) and PLA (at 70°). Code I0059 Available Price €5.75
PCB Heated Bed MK3 Alu 3mm 12V 24V 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Available Price €11.99
Heated Bed PCB MK2B 3D Reprap Printer Heated Bed PCB MK2B 3D Reprap Printer features: - Measurements: 214mm x 214mm Code I0001 Available Regular price €8.36 -€2.00 Price €6.36
PCB Heated Bed MK3 Alu 3mm 12V 24V 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Available Price €11.99
Heated Bed PCB MK2B 3D Reprap Printer Heated Bed PCB MK2B 3D Reprap Printer features: - Measurements: 214mm x 214mm Code I0001 Available Regular price €8.36 -€2.00 Price €6.36
PCB Round Heated Bed 200mm MK2Y 3D Reprap Printer Hot bed MK2Y powered by 12V current with a power of 90W. The maximum recommended temperature of the hot bed is between 110° - 135°, which is sufficient for ABS (at 110°) and PLA (at 70°). Code I0059 Available Price €5.75