Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.90 -€0.41 Price €1.49
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
3S BMS 25A 12.6V 18650 PCM PCB Circuit Charging Module. In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0106 Available Price €4.49
Mini Fan 12V 2x 3D Printer Cables Mini Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 80mA - Speed: 2600rpm +/- 10% - Temperature operating: -10 ° C to 65 ° C - Cable length: 12cm - Dimensions: 25mmx 25mm x 10mm Code I0027 Available Price €1.59
Extruder Kit MK8 Bowden Aluminium 1.75mm 3D Printer Creality Ender Extruder MK8 Bowden for Creality 3D Ender 3, CR-7, CR-8, CR-10, CR-10S, CR-10 S4 y CR-10 S5. Includes: MK8 extruder complete push system. Square part dimensions: 42x42mm. Part dimensions - handle L: 56x28mm Code I0183 Last items in stock Price €14.95
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
Support for 30mm Fan E3D V6 3D Printer Support for 30mm Fan E3D V6 3D Printer features: - Support for 30mm fan - Compatible with E3D V6 - For hotels with 22mm diameter - E3D V6 Cooling Fan Cover 3D Printer - Unique design surrounded, close contact with the radiator, gather wind around the radiator so that the heating block can work normally Code I0047 Available Price €1.19
PETG White Filament 1.75mm 1kg PETG White Filament 1.75mm 1kg features: - Premium Coil for 3D Printer- 1000g coil- Extrusion temperature: 220ºC - 250ºC- Hot bed temperature / Hotbed: 40ºC- 70ºC Code I0277 ✗ Out-of-Stock Price €22.70
Support for 30mm Fan E3D V6 3D Printer Support for 30mm Fan E3D V6 3D Printer features: - Support for 30mm fan - Compatible with E3D V6 - For hotels with 22mm diameter - E3D V6 Cooling Fan Cover 3D Printer - Unique design surrounded, close contact with the radiator, gather wind around the radiator so that the heating block can work normally Code I0047 Available Price €1.19
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 ✗ Out-of-Stock Price €1.95
Precision Micro Drills 0.5mm pack 10pcs Kit of Micro Steel Drill Bits to eliminate jams in nozzles of 3D printers, CNC Code I0165 Available Regular price €5.99 -€1.00 Price €4.99
Double-Sided Adhesive Tape 5mm 50m Double-Sided Adhesive Tape 5mm 50m features: - Transparent double-sided adhesive tape, 5mm wide and 50m long- After its removal it leaves no residue- Given its versatility it will allow multiple use options Code I0147 Last items in stock Price €2.90
4x Springs Leveling Hot Bed 3D Printer 4x Springs Leveling Hot Bed 3D Printer features: 3D Springs printer Bed level extruder for RepRap Prusa Mendel - A strong spring for 3D Printer Extruder- Excellent elasticity, resistance to fatigue- Nickel plating, corrosion resistance, high hardness- Material: Carbon steel- Outside diameter: 7.5mm- Inner diameter: 5 mm- Spring height: 20 mm- Quantity of the ring: 9 rings- Surface treatment: Nickel-plating Code I0049 Available Price €0.39
Micro Bits for 3D Printer Nozzle pack 10pcs Kit of Micro Steel Drill Bits to eliminate jams in nozzles of 3D printers, CNC Characteristic: - Diameter: 0.2 / 0.3 / 0.4 / 0.5 / 0.6 / 0.7 / 0.8 / 0.9 / 1.0 / 1.2 mm - Shank diameter approx . 3.2mm - Total length approx. 38mm - Material: Steel - Quantity: 10 units Code I0110 Available Price €4.99
Extruder Kit MK8 Bowden Aluminium 1.75mm 3D Printer Creality Ender Extruder MK8 Bowden for Creality 3D Ender 3, CR-7, CR-8, CR-10, CR-10S, CR-10 S4 y CR-10 S5. Includes: MK8 extruder complete push system. Square part dimensions: 42x42mm. Part dimensions - handle L: 56x28mm Code I0183 Last items in stock Price €14.95
3x Heat Sink Aluminium Adhesive A4988 DRV8825 3x Heat Sink Aluminium Adhesive A4988 DRV8825 features: - Package includes: 3x Heatsink with adhesive - Ideal for DRV8825, A4988 etc - Dimensions: 9 x 9 x 5mm Code I0046 Available Price €0.35
2x Spring Tensioning Strap Printer 2x Spring Tensioning Strap Printer features: - Use with 6mm strap - Timing Belt GT2 Tensioner Spring for RepRap Prusa Mendel 3D printer - Fits 3D printer timing belt system - Fits belt width: less than or equal to 6mm - Constant force to keep belt reasonably tight to avoid losing steps, skipping steps or unwanted movements - Material: Metal - Silver color - Size: 12 x 12 x 8 mm (length x width x height) - Quantity: 2 units Code I0048 Available Price €0.35
Heat Sink Aluminium Adhesive Radiator 25x25 Heatsink aluminium adhesive radiator for electronics components. Especially recomanded for passive cooling of Stepper Drive, MOSFET, VRM, Vram, IC Chips etc. Good thermal conductivity, reduce the risk of hardware failure due to overheating, made of high quality Aluminum. Code A0117 Available Price €0.85
Support for 30mm Fan E3D V6 3D Printer Support for 30mm Fan E3D V6 3D Printer features: - Support for 30mm fan - Compatible with E3D V6 - For hotels with 22mm diameter - E3D V6 Cooling Fan Cover 3D Printer - Unique design surrounded, close contact with the radiator, gather wind around the radiator so that the heating block can work normally Code I0047 Available Price €1.19
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 ✗ Out-of-Stock Price €1.95
Precision Micro Drills 0.5mm pack 10pcs Kit of Micro Steel Drill Bits to eliminate jams in nozzles of 3D printers, CNC Code I0165 Available Regular price €5.99 -€1.00 Price €4.99
Double-Sided Adhesive Tape 5mm 50m Double-Sided Adhesive Tape 5mm 50m features: - Transparent double-sided adhesive tape, 5mm wide and 50m long- After its removal it leaves no residue- Given its versatility it will allow multiple use options Code I0147 Last items in stock Price €2.90
4x Springs Leveling Hot Bed 3D Printer 4x Springs Leveling Hot Bed 3D Printer features: 3D Springs printer Bed level extruder for RepRap Prusa Mendel - A strong spring for 3D Printer Extruder- Excellent elasticity, resistance to fatigue- Nickel plating, corrosion resistance, high hardness- Material: Carbon steel- Outside diameter: 7.5mm- Inner diameter: 5 mm- Spring height: 20 mm- Quantity of the ring: 9 rings- Surface treatment: Nickel-plating Code I0049 Available Price €0.39
Micro Bits for 3D Printer Nozzle pack 10pcs Kit of Micro Steel Drill Bits to eliminate jams in nozzles of 3D printers, CNC Characteristic: - Diameter: 0.2 / 0.3 / 0.4 / 0.5 / 0.6 / 0.7 / 0.8 / 0.9 / 1.0 / 1.2 mm - Shank diameter approx . 3.2mm - Total length approx. 38mm - Material: Steel - Quantity: 10 units Code I0110 Available Price €4.99
Extruder Kit MK8 Bowden Aluminium 1.75mm 3D Printer Creality Ender Extruder MK8 Bowden for Creality 3D Ender 3, CR-7, CR-8, CR-10, CR-10S, CR-10 S4 y CR-10 S5. Includes: MK8 extruder complete push system. Square part dimensions: 42x42mm. Part dimensions - handle L: 56x28mm Code I0183 Last items in stock Price €14.95
3x Heat Sink Aluminium Adhesive A4988 DRV8825 3x Heat Sink Aluminium Adhesive A4988 DRV8825 features: - Package includes: 3x Heatsink with adhesive - Ideal for DRV8825, A4988 etc - Dimensions: 9 x 9 x 5mm Code I0046 Available Price €0.35
2x Spring Tensioning Strap Printer 2x Spring Tensioning Strap Printer features: - Use with 6mm strap - Timing Belt GT2 Tensioner Spring for RepRap Prusa Mendel 3D printer - Fits 3D printer timing belt system - Fits belt width: less than or equal to 6mm - Constant force to keep belt reasonably tight to avoid losing steps, skipping steps or unwanted movements - Material: Metal - Silver color - Size: 12 x 12 x 8 mm (length x width x height) - Quantity: 2 units Code I0048 Available Price €0.35
Heat Sink Aluminium Adhesive Radiator 25x25 Heatsink aluminium adhesive radiator for electronics components. Especially recomanded for passive cooling of Stepper Drive, MOSFET, VRM, Vram, IC Chips etc. Good thermal conductivity, reduce the risk of hardware failure due to overheating, made of high quality Aluminum. Code A0117 Available Price €0.85