20x Zener Diode BZX55C3V3 3.3V 500mW DO-35 0.5W 3V3

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 70-80LM
- Ã beam angle: 120 degrees
- Color emission: green

RGB LED Strip WS2812B Black 1m 30 LED/M IP65 features:
- RGB LED WS2812B
- WS2812B are LEDs that have integrated logic, making it possible to vary the color of each LED in a way individual
- WS2812B includes a built-in inside each LED, which allows each pixel to be accessed individually
- For this reason, these types of LEDs are called individually indexable.
- They are based on the 5050 LEDs
- 30 individually indexable LED diodes
- 24-bit color control (8-bit PWM per channel)
- 16.8 million colors per LED
- Communication One-wire
- Power: 5 V
- Width: 11 mm
- Thickness: 2.6 mm
- Length: 1 meter
- Consumption: 1.8A (all white)
- Waterproof
- With 3M adhesive

COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)
- The light intensity is greater without needing to concentrate so much the beam of light
- Greater durability
- Angle of opening up to 160ºC
- Multidirectional light - Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little thermal silicone in each of the placement centers of the diodes
- The thermal paste increases the thermal transfer between the diode and the metal plate used as circuit

COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)
- The light intensity is greater without concentrating the beam of light
- Greater durability
- Angle of opening up to 160ºC
- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.
Place a little thermal silicone in each of the diode placement centers.

Aluminum Heat Sink 15cm 2cm LED 1W 3W features:
Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm.

5mm multicolor LED with automatic color change. 7 different colors are emitted and the blinking is fast.

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them.

Characteristic:

- Voltage: 3.2-3.6V

- Current : 700mA

- Luminous flux: 5-8LM

- Beam angle: 140 degrees

- Colour emission: Ultraviolet

COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)
- the light intensity is greater without the need to concentrate the beam of light
- greater durability
- opening angle of up to 160ºC
- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.

LED 5mm RGB 4 Pins cathode commun with clear water lens.