Traffic light LED red yellow green 5V display module Arduino

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Connector BLS03 Female/Female 3 Pins RoHS Single Row features:
- Step between pins: 2.54 mm
- Manufacturer: Maritex
- Number of connections: 3 in a single row
- Type: Female / Female
- RoHS standard

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

High capacity 18650 battery made of Li-ion technology with electronic protection and integrated micro USB socket for direct charging

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC

10x Female-Female Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have female header contacts at either end
-Compatible with male connectors 2,54mm
-High quality and good working conditions
-Easy to install and use