Diodes

Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them.
Characteristic:
- Chip 28x47mil
- Voltage: 2.85-3.85V
- Current: 350mA - Luminous flux: 120-130LM
- Beam angle: 130 degrees

Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them.
Characteristic:
- Chip 28x47mil
- Voltage: 3.0-3.2V
- Current: 300mA - Luminous flux: 120-130LM
- Beam angle: 130 degrees

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 2.2-2.4V
- Current: 300mA
- Luminous flux: 40-50LM
- Ã beam angle: 120 degrees
- Color emission: red

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 3.2-3.4V 
- Current: 350mA 
- Luminous flux: 100-110LM 
- Ã beam angle: 140 degrees 
- Color emission: pink

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 70-80LM
- Ã beam angle: 120 degrees
- Color emission: green

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 2.2-2.4V
- Current: 300mA
- Luminous flux: 40-50LM
- Ã Beam angle: 120 degrees
- Color emission: yellow / orange

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 20-30LM
- Ã beam angle: 120 degrees
- Color emission: blue

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil
- Voltage: 3.1-4.1V
- Current: 700mA
- Luminous flux: 39-55LM
- Ã beam angle: 120 degrees
- Color emission: blue

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them.

Characteristic:

- Voltage: 3.2-3.6V

- Current : 700mA

- Luminous flux: 5-8LM

- Beam angle: 140 degrees

- Colour emission: Ultraviolet

3x LED Base Plate Heat Sink 1W 3W 5W features:
- Outside diameter: 20mm
- Quantity: 3 units