5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.44
LED 1W UV SMD - Ultraviolet Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Voltage: 3.2-3.6V - Current : 700mA - Luminous flux: 5-8LM - Beam angle: 140 degrees - Colour emission: Ultraviolet Code P0162 Available Price €1.15
Mini Submersible Water Pump DC 3V 120L/H Characteristic: - Operating voltage: 3-6V - Max flow: 80-120 l / h - Maximum pumping height: 40-110cm - Continuous working time of 500 hours - Cable length: 20cm - Inside outlet diameter: 5 mm - Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm Code M0040 Available Regular price €2.06 -€0.51 Price €1.55
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.81
LED diode 1W White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0043 ✗ Out-of-Stock Price €0.81
PLA Filamento 1.75mm 0.85kg Burgundy color burdeo Premium Bobina para Impresora 3D Code I0404 Backorder Price €14.45
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Regular price €8.22 -15% Price €6.99
LED Diode COB 3W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0146 ✗ Out-of-Stock Price €1.09
LED Power Diode COB 5W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0028 Available Price €1.74
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €13.18 -15% Price €11.20
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.05
3x LED Base Plate Heat Sink 1W 3W 5W 3x LED Base Plate Heat Sink 1W 3W 5W features: - Outside diameter: 20mm- Quantity: 3 units Code P0039 Available Price €0.41
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED 1W Red SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã beam angle: 120 degrees - Color emission: red Code P0044 Available Price €0.81
LED Power Diode COB 10W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0148 Available Price €1.74
LED 1W UV SMD - Ultraviolet Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Voltage: 3.2-3.6V - Current : 700mA - Luminous flux: 5-8LM - Beam angle: 140 degrees - Colour emission: Ultraviolet Code P0162 Available Price €1.15
LED Diode COB 3W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0146 ✗ Out-of-Stock Price €1.09
LED Power Diode COB 5W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0028 Available Price €1.74
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €13.18 -15% Price €11.20
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.05
3x LED Base Plate Heat Sink 1W 3W 5W 3x LED Base Plate Heat Sink 1W 3W 5W features: - Outside diameter: 20mm- Quantity: 3 units Code P0039 Available Price €0.41
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.81
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.09
LED 1W Red SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã beam angle: 120 degrees - Color emission: red Code P0044 Available Price €0.81
LED Power Diode COB 10W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0148 Available Price €1.74
LED 1W UV SMD - Ultraviolet Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Voltage: 3.2-3.6V - Current : 700mA - Luminous flux: 5-8LM - Beam angle: 140 degrees - Colour emission: Ultraviolet Code P0162 Available Price €1.15