Arduino

Sonoff power supply for camera Sonoff GK-200MP2-B black (M0802050002) 5V 1.2A.

The 3.5x1.3mm plug is also popular, e.g. in USB HUBs, where it can also be used.

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased.

This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person.

Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid.

This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together.

MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V.

This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds

This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads.

This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person.

SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project.

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino

This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

It is a version without headers of a popular BOB-09868 from SparkFun.

In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005).

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors

This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module  is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use.

The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements.

WiFi Smart Wall Switch Sonoff T1 Gang 86

Smart WiFi RF APP Touch Control Wall Light Switch features:
works with Amazon Alexa,  Google Assistant DIY Smart Home, Nest  via iPhone Android.

Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies.

SparkFun Hamburger speaker is a high quality speaker in a small form and with even smaller price. You wouldn't believe you can get a quality product for less than 7€, right? Well, we couldn't believe that as well, but SparkFun makes that possible.

This small GPS breakout is yet another Qwiic module from SparkFun as per usual based on I2C - meaning that you can keep your serial port free for other applications. The board features XA1110 GPS module from GTOP and MediaTek MT3333 chipset already loaded with SparkFun firmware enabling clean and easy use of both ports. 

It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328.

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV.

This LED power amplifier with a Sonoff power adapter is designed to extend existing Sonoff LED lighting systems. With this signal amplifier, you have the option to extend your Sonoff LED strip system, as the included power adapter provides sufficient power.

The perfect solution for not worrying about the length required on your RGB LED strip, now with a WiFi driver compatible with the eWeLink APP and voice assistants like Google Home or Alexa. Also includes a 24-key IR remote control.

You will be able to turn on and control your strip lights anytime and anywhere, and control it with just a click on your smart phone or tablet via APP eWeLink, or voice assistants, without time and distance limitations.

The Sonoff IFan03 is an intelligent controller for ceiling fans with light that allows us to control it intelligently, either by the eWeLink application, by means of 433MHz RF control or by voice assistants such as Alexa or Google Home.

Create your own scenes, turn on the light and/or the fan and adjust its speed, programming it to the hours you want.

This E27 bulb adapter will allow you to control its on and off by WiFi and to control your lamps by the free eWeLink APP, with which you can create routines and scenes, by IFTTT, or also by voice assistants such as Alexa or Google Home.

Intelligent 5 metre LED strip by WiFi and RF, great for creating any atmosphere in any room. Change its colour and rhythm from your mobile phone or its remote control. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes.

5 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

This cable is designed to facilitate the extension of the sensor cable, being perfect for applications that require greater distances. They can be joined together to extend your sensors up to a maximum length of 60 metres.

This 1-meter probe uses the original DS18B20 temperature sensor chip. The DS18B20 is a waterproof temperature sensor/thermometer. It is waterproof, moisture proof and rustproof with the high quality stainless steel tube encapsulated. This is a spare part or accessory used in SONOFF TH10 / TH16.

433.92 MHz radio receiver module that allows you to also control it via a radio remote control. You can control each channel either by remote control, the free APP "eWeLink" or with wizards such as Alexa or Google Home. This will allow you to create scenes, schedules, and much more. Its relay supports up to 4 devices simultaneously. Each device can be powered by 5-24 V DC.

SONOFF D1 Smart Dimmer Switch is a smart dimmer switch that offers smart light control solutions perfect for your home or workplace, controlled either by the eWeLink application, via 433MHz RF control or by voice assistants such as Alexa or Google Home.

Create your own scenes, turn the light on at the most appropriate level, or schedule it at the times you want

Elegant WIFI controlled touch wall light switch with 3 switches. SONOFF TX offers you perfect intelligence control solutions for your home or workplace. Compatible with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone or Android.

SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches!

2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

SONOFF AL010 RJ9 Adapter dedicated to sensors compatible with the previous Sonoff TH16 series, where there was a Mini Jack connector.

Suitable for temperature and humidity sensor AM2301 and Si7021, waterproof temperature sensor DS18B20 and soil moisture sensor MS01.

NSPanel offers intelligent control of home appliances: lighting, thermostat, curtains, windows and wall switches. A colour touch screen with two buttons displays all the necessary information and allows you to conveniently navigate through the device's menu, making the Sonoff NSPanel the ideal control centre for your home. The NSPanel is designed to be mounted on the Sonoff switch frame (switch frame not included).

NSPanel offers intelligent control of home appliances: lighting, thermostat, curtains, windows and wall switches. A colour touch screen with two buttons displays all the necessary information and allows you to conveniently navigate through the device's menu, making the Sonoff NSPanel the ideal control centre for your home. The NSPanel is designed to be mounted on the Sonoff switch frame (switch frame not included).

Elegant WIFI controlled touch wall light switch with 2 switches. SONOFF TX offers you perfect intelligence control solutions for your home or workplace. Compatible with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone or Android.

This cable is designed to facilitate the extension of the sensor cable, being perfect for applications that require greater distances. They can be joined together to extend your sensors up to a maximum length of 60 metres.

SONOFF DUALR2 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR2 control switch is equivalent to 2 Sonoff basic switches!