Kontakt PCB PLUS Spray 400ml The PCB PLUS cleaner is designed for printed circuit boards.Dissolves waste flux, including resin.The liquid does not attack the substrate or the structural components of the printed circuit boards.The special brush to remove particles and smaller debris. Perfect for cleaning PCB after repair and assembly.PCB Plus Cleanser Spray 400ml features:- Form: spray- Capacity: 400mlApplication:- The product does not leave deposits- It evaporates very fast- Eliminates waste after welding- Perfect in any electronic service- The product does not react with most plastics used in electronics Code Q0071 Available Price €8.22
Potentiometer B1K Linear Potentiometer B1K Linear features: -1k OHM kΩ - linear potentiometer 1k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0065 Available Price €0.82
High Precision i2c Digital Current Sensor Module GY-INA219 GY-219 The INA219 breakout board can be powered by the 5V or 3V pin on your Arduino and communicates via I2C. If you want to sense an Direct Current (DC) with high accuracy and voltage too, we suggest you to use this sensor. I2C sensor can easily interfaced with arduino. It uses 4 pins only. Code M0212 Available Price €2.80
Integrated Circuit Supports DIP8 Width 10.16 mm Integrated Circuit Supports DIP8 Width 10.16 mm features: - Type: DIP DIL- Total number of pins: 8- Step between pins: 2.54 mm- Material: Polybutylene terephthalate- Length: 7.62 mm- Width: 10.16 mm- Temperature min .: -25 °C- Max temperature: +85 °C- RoHS compliant Code Z0005 Available Price €0.08
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
Silicone Thermal Paste Syringe 25g Silicone Thermal Paste Syringe 25g features: - Density at 20°C: 2.58 G/cm3- Flashpoints: 350°C- Freezing point: -50°C- Coefficient of refraction: 1.405,- Specific temperature at 50°C: 0.243 Cal/g K- Co-efficient global heat transfer at 0-150°C: 0.78 W/m K- Constant dielectric at 100 Hz: 4.7 (± 0.1)- Cross resistance: 5 x 10 to the power 14 Ohm x cm- Loss rate at f = 100 Hz: 0.020 (± 0.003)- Range of operating temperature: -50~200°C Code Q0008 Available Price €3.96
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm Tin ideal for application in consumer electronics circuits.Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm features:- 100gr. 1.2mm diameter welding wire- 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0003 ✗ Out-of-Stock Price €7.40
Sodium Persulfate - etching agent for PCB and copper - pack 100g Chemical substance for recording printed circuits and copper. Unlike ferric chloride, sodium persulfate is colorless, odorless, does not stain clothes and does not turn blue when it runs out. Easy to dissolve. It acts very regular with guarantee of contour sharpness. Code Q0053 Available Price €2.36
Transparent Insulating PCB Varnish 60 1 Liter Necessary for the protection of printed circuits.PCB varnish of high quality for manufacturing, repair and maintenance.Prevents the oxidation of printed circuit boards during intermediate storage. Transparent Insulating PCB Varnish 60 1 Liter features: - A protective film, transparent- Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination- It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate the protective film- PVB 60 is used, for example, in the storage of printed circuit boards and material to be welded, such as welding terminals or conductors- Application temperature: od -40 ° C + 60 ° C Code Q0046 Backorder Price €17.43
Technical Petrolatum 35g - The electrical products and lubricants of the bearings- Its working temperature is up to 30 °C Technical Vaseline for Contacts and Bearings 35g features: - Solid product- White color- Specific smell- Melting point: 56 °C- Ignition temperature: 220 °C- Density at 20 °C: 822 kg / m3- Maximum temperature of use: 30 °C- Solubility in water: partial Code Q0081 Available Price €1.31
Graphite Varnish 2x1.5ml Graphite Varnish cCan be used for the elimination of discontinuities in the graphite layer in printed circuits. Creation or reconstruction of routes in printed circuits of low intensity. Protection of silver contacts from harmful direct contact of silver with rubber (in remote controls) Code Q0073 Available Price €3.21
Technical Petrolatum 65ml Vaseline Technical Grease 20g features:- Lubricates moving surfaces, bearings,- Protects metal parts against corrosion and electrical contacts- Protects and preserves rubber and plastic- It can be used as mounting grease- Eliminates squeaks- Reduces and decreases friction Code Q0064 Available Price €1.15
Technical Petrolatum with Dispenser 65ml Technical Petroleum Jelly with Dispenser 65ml features: - Used for protecting electric contacts, lubricating bearings- Max. operating temperature: 30°C Code Q0063 Available Price €2.80
Insulating Varnish Spray 400ml Necessary for the protection of printed circuits.PCB varnish of high quality for manufacturing, repair and maintenance.Prevents the oxidation of printed circuit boards during intermediate storage. Insulating Varnish Spray 400ml features:-A protective film, transparent.-Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination-It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate theprotective film-PVB 16 is used, for example, in the storage of printed circuit boards and material that is going to besoldier, such as welding terminals or conductors.-Temperature of application: od -40 ° C + 60 ° C. Code Q0014 Last items in stock Price €9.88
Universal developer for photo varnish and positive printed circuit boards PCB The product provides a good development quality, protecting the sharpness of the color. The formulation is free of NaOH, which significantly increases safety at work. Universal developer for photo varnish and positive printed circuit boards PCB. Code Q0094 Available Price €2.39
PVB Varnish 16 Spray 100ml Necessary for the protection of printed circuits. PCB varnish of high quality for manufacturing, repair and maintenance. Code Q0117 ✗ Out-of-Stock Price €3.84
Varnish Flux LT-4 - The product protects PCB plates, allows for easier welding- The product protects the printed circuit boards against oxidation and corrosion during storage.- This allows a faster welding and avoids the "cold welding".- The application method allows easy distribution of the product on the plates.- Can be used during production, repair, maintenance and service.Flux Varnish LT-4 Plate Protector features:- Shape: Spray- Capacity: 100ml- Rosin RMA- Meets the requirements of DIN 8511, F-SW-31, PN EN 29454 1.1.1.A.Application:- PCB protection against oxidation,- Applied in the production of printed circuit boards immediately after engraving, Code Q0070 Available Price €4.92
Transparent Insulating PCB Varnish 60 1 Liter Necessary for the protection of printed circuits.PCB varnish of high quality for manufacturing, repair and maintenance.Prevents the oxidation of printed circuit boards during intermediate storage. Transparent Insulating PCB Varnish 60 1 Liter features: - A protective film, transparent- Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination- It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate the protective film- PVB 60 is used, for example, in the storage of printed circuit boards and material to be welded, such as welding terminals or conductors- Application temperature: od -40 ° C + 60 ° C Code Q0046 Backorder Price €17.43
Technical Petrolatum 35g - The electrical products and lubricants of the bearings- Its working temperature is up to 30 °C Technical Vaseline for Contacts and Bearings 35g features: - Solid product- White color- Specific smell- Melting point: 56 °C- Ignition temperature: 220 °C- Density at 20 °C: 822 kg / m3- Maximum temperature of use: 30 °C- Solubility in water: partial Code Q0081 Available Price €1.31
Graphite Varnish 2x1.5ml Graphite Varnish cCan be used for the elimination of discontinuities in the graphite layer in printed circuits. Creation or reconstruction of routes in printed circuits of low intensity. Protection of silver contacts from harmful direct contact of silver with rubber (in remote controls) Code Q0073 Available Price €3.21
Technical Petrolatum 65ml Vaseline Technical Grease 20g features:- Lubricates moving surfaces, bearings,- Protects metal parts against corrosion and electrical contacts- Protects and preserves rubber and plastic- It can be used as mounting grease- Eliminates squeaks- Reduces and decreases friction Code Q0064 Available Price €1.15
Technical Petrolatum with Dispenser 65ml Technical Petroleum Jelly with Dispenser 65ml features: - Used for protecting electric contacts, lubricating bearings- Max. operating temperature: 30°C Code Q0063 Available Price €2.80
Insulating Varnish Spray 400ml Necessary for the protection of printed circuits.PCB varnish of high quality for manufacturing, repair and maintenance.Prevents the oxidation of printed circuit boards during intermediate storage. Insulating Varnish Spray 400ml features:-A protective film, transparent.-Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination-It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate theprotective film-PVB 16 is used, for example, in the storage of printed circuit boards and material that is going to besoldier, such as welding terminals or conductors.-Temperature of application: od -40 ° C + 60 ° C. Code Q0014 Last items in stock Price €9.88
Universal developer for photo varnish and positive printed circuit boards PCB The product provides a good development quality, protecting the sharpness of the color. The formulation is free of NaOH, which significantly increases safety at work. Universal developer for photo varnish and positive printed circuit boards PCB. Code Q0094 Available Price €2.39
PVB Varnish 16 Spray 100ml Necessary for the protection of printed circuits. PCB varnish of high quality for manufacturing, repair and maintenance. Code Q0117 ✗ Out-of-Stock Price €3.84
Varnish Flux LT-4 - The product protects PCB plates, allows for easier welding- The product protects the printed circuit boards against oxidation and corrosion during storage.- This allows a faster welding and avoids the "cold welding".- The application method allows easy distribution of the product on the plates.- Can be used during production, repair, maintenance and service.Flux Varnish LT-4 Plate Protector features:- Shape: Spray- Capacity: 100ml- Rosin RMA- Meets the requirements of DIN 8511, F-SW-31, PN EN 29454 1.1.1.A.Application:- PCB protection against oxidation,- Applied in the production of printed circuit boards immediately after engraving, Code Q0070 Available Price €4.92