MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 ✗ Out-of-Stock Price €3.55
Arduino Due Arduino Due is the perfect board for powerful large-scale Arduino projects. This is the only Arduino microcontroller based on the Microchip SAM3X8E with an Arm Cortex-M3® processor. If other basic boards are not enough for your ideas and demands, this one will surely satisfy them. Add to this 54 pins (54 digital input/output pins, 12 analog inputs, 2 DAC, 2 CAN and 4 UARTS) and you have a board that will not stop before any obstacle. Code BAR62 Last items in stock Price €46.28
Yellow silicone protective cover for BBC Micro:Bit V2 Protective cover used for micro: bit. The cover has two different sides, dot matrix display area, finger usage area on the front. Micro USB interface, power interface and reset button on the back side. It can be installed on a micro: bit board to make your work more charming and fun. Weight: 10g Size: 5,65 cm * 3,7 cm Material: gel silica (environmental protection material) Code RA137 ✗ Out-of-Stock Price €3.72
Temperature Sensor Module MLX90614ESF-BAA GY-906 The GY-906 BAA is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, within 3 cm the precision is higher, approximately 0.5 degrees Code S0145 Available Price €8.22
BBC micro:bit V2.21 - WiFi Single Board Micro-Computer, BLE 5.0, Microphone + Speaker + Accelerometer The novelty of micro:Bit v2.21 for a more lively introduction to technology for children. The micro:bit is a pocket computer that can be encoded, customized and controlled for the implementation of digital ideas and games. It measures just 4x5cm and features a fun and easy to use design, so users can create anything from games and animations to slick stories at school, at home or anywhere - all it takes is imagination and creativity. It is fully programmable. This means that each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer, Bluetooth 5.0 technology, microphone and speaker. It contains a quick start guide in the same package. Code B0120 Available Regular price €17.31 -€1.00 Price €16.31
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.06 -€0.50 Price €1.56
SW-520D Vibration Metal Tilt Sensor Detects changes in the sensor angle and returns to the digital value. 5x SW-520D Vibration Metal Tilt Sensor features: - Contact resistance: Code S0020 Available Price €0.37
2x AAA 3V battery holder for Micro:bit Weight: 12.7g Box size: 62 * 25 * 10 mm Code PP037 Available Price €1.64
Lilypad Arduino compatible USB ATmega32u4 Board The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restartIt contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port. Code M0147 Available Regular price €6.60 -€1.00 Price €5.60
Lilypad Arduino compatible USB ATmega32u4 Board The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restartIt contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port. Code M0147 Available Regular price €6.60 -€1.00 Price €5.60