Rocker switch KCD4 momentary 15A 250V Double (ON)-OFF Red 4-pin The AC 250V 15A 4-pin DPST (on/off) type rocker switch. Code K0401 Available Price €1.90
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
Servo with Rotation 180 Servo Motor Type S3003 Servo with Rotation 180 Servo Motor Type S3003 features: - Model Aircraft Futaba Arduino Robotics - Operating Voltage: 4.8V to 6V - Max Torque: 4.1kg / cm (6V) - Operating speed: 0.23sec / 60 degrees (4.8V), 0.19sec / 60 degrees (6V) - Max radius: 180º - Temperature range: -20 + 60 C degrees - Weight: 38 g - Cable length: 26cm - Dimensions: 40.5 x39x 20 mm - Servo connector: JR - Chinese manufacturing Code R0018 Available Regular price €6.29 -€0.30 Price €5.99
LED 10-Segment Bar Graphics Display Red LED 10-Segment Bar Graphics Display Red features: - Bargraph LED display - Number of segments: 10 - Size: 5mm - Dimensions: 25x10mm - Material GaAsP / GaP - Color: red - Wavelength: 635 nm - Vf / forward /2.1 V - I fw / forward / 30 mA - Iv / Ifw = 20mA / 4 mcd - Number of terminals: 20 Code P0100 ✗ Out-of-Stock Price €1.13
300 Pieces LED Diodes 3mm 5mm red green yellow blue white Set of 300 diodes packed in a handy box. Lens colour: red, green, yellow, yellow, blue - diffuse, light white. Code P0104 Available Regular price €7.95 -€1.46 Price €6.49
5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.95
Arduino Mkr Wifi 1010 Arduino MKR WiFi 1010 ( ABX00023 ) es la evolución del MKR1000 y está equipado con un módulo ESP32 de u-blox. Su objetivo es acelerar y simplificar la creación de prototipos de aplicaciones IoT basadas en WiFi gracias a la flexibilidad del módulo ESP32 y su bajo consumo de energía. CONECTIVIDAD USB MICRO TIPO B WIFI & BLE Code ABX023 Last items in stock Price €46.90
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90