Flat Cable IDC10 Female Connector 2.54

88x M3 Nylon Separator Kit Screw Hex Nut features:
- Hexagonal M3 made of nylon for screws and fasteners on PCB boards, model airplanes, DIY projects
- Can be used in prototype projects and robotics
- Box dimension: 128x 66x 24mm
- Quantity: 88 units
- Color: black

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

Batch of 600 Units 1/4W Resistors Various values Ohm Ω features:
- Each lot contains
(30 x 20 units):
10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M
- Tolerance: ± 5%
- Power: 0.25W

Male Double Row 80 Pin Header 2x40 features:
- Type: Male
- Insertion position: Vertical
- Separation between pins: 2.54mm
- Quantity: 1 unit 2x40 pins

The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery

Polarity cannot be reversed by mistake.
90 degree angle connector. JST PHR-2 Connector Male Angle 3 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: female connector Connector class: male Connector type: conduit-plate Contactor raster: 2mm Number of pins: 3 Electrical mounting: THT Working voltage: 100V Working current: 2A Working temperature: -25 ... 85 ° C Spatial orientation: horizontal data sheet PH series

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

Ideal for projects with ARDUINO, Smart Car
Detects transparent and translucent obstacles
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:
- Current consumption: up to 100 mA
- Supply voltage 5V
- Current consumption <25mA
- Response time of 2 ms
- Measured distance: 3-80cm 15st angle
- Screw to adjust the sensitivity, the back
- Output status led indicator
- Operating temperature: -25°C - + 55°C
- Material: high-strength plastic
- Type of output: normally open, NPN
- Dimensions: 18 mm in diameter, Length 45 mm
- Cable length 55cm
- Departures:
      - Brown: +
      - Blue: -
      - Black: OUT