2x IDC 10 female connector for flat cable AWG 1.27

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features:

- Based on the LM2596S-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 1.25v - 32v DC (adjustable)
- Voltage of Input: 3.2v - 35v DC
- Max Output Current: 3A (with heat sink)
- Ripple at output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 2.5%
- Operating Temperature: -40ºC to + 85ºC
- Measurements 43x 21x 14 mm

2x Banana Connector Diameter 4mm Red and Black features:
- Length: 40 mm
- Diameter plug: 4mm
- Quantity: 2 units

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Female DC Power Connector Jack 2.1x5.5mm features:
- Ideal for connecting without welding
- It has two screws in the tip for positive and negative cable screwdriver

It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Arduino Protoboard Breadboard 400 points features:
-400 Connections
-Linkable with other Plates
-Base with adhesive to attach it to the work surface
-Measures 82x55x8 mm

Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter.
Similar to the Arduino line , It is one of the smallest boards on the market.
Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others.
You can use many of the same Arduino libraries and you have your own on the digispark wiki. Arduino compatible Attiny85 Digispark board features:
- USB power supply
- External power supply (7v-35v DC 12v maximum recommended)
- 5V DC 500mA regulator on board
- Programmable with the Arduino IDE
- Loaded with Micronucleus bootloader