Blue silicone protective cover for BBC Micro:Bit Protective cover used for micro: bit. The cover has two different sides, dot matrix display area, finger usage area on the front. Micro USB interface, power interface and reset button on the back side. It can be installed on a micro: bit board to make your work more charming and fun. Weight: 10g Size: 5.5 cm * 6.5 cm Material: gel silica (environmental protection material) Code RA045 ✗ Out-of-Stock Price €5.00
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Last items in stock Price €1.99
Male 40 Pin Header 1x40 Male 40 Pin Header 1x40 features: Type: Male, Insertion position: Vertical, Separation between pins: 2.54mm Code K0138 Available Price €0.69
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.49
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
Ethernet Patchcord UTP 5e 2m Ethernet Patchcord UTP 5e 2m features: Code K0273 Available Price €2.59
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
40x Female-Female Cable 10cm 40x Female-Female Cable 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont female connectors on both ends - Compatible with 2.54mm male connectors - High quality and good working conditions - Easy to install and use Code K1005 Available Price €1.99
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €7.95
Black Housing for Raspberry Pi 2, 3, Model B, B+ Black Housing for Raspberry Pi 2, 3, Model B, B+ features: - Black Case Shell Box - Housing for Raspberry Pi2, Pi3, B and B + - Color: Black - Made of ABS - Dimension: 95x 62x 26mm Code RA002 Available Price €2.70
USB to Micro USB On/Off Switch for Arduino Charger Cable It has an ON / OFF switch that will cut off power when you don't need it. USB to Micro USB On/Off Switch Arduino Charger Cable features: - Black color - Length: 150cm - Maximum current 1A Code K0054 Available Price €2.85
Camera IMX219-160 8MP 160° FOV - Compatible with NVIDIA Jetson Nano/ Xavier NX It is an 8-megapixel camera with a 160-degree field of view, equipped with a chip Sony IMX219. The camera is designed for NVIDIA Jetson Nano and NVIDIA Jetson Xavier NX development kits. Code SS046 Last items in stock Price €35.99
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.88
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
GPS Mini Station NEO-6M-0-001 with EEPROM SMA IPEX Ports It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip. The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed. Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC - Operating current: 45 mA - Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds - Navigation update: 5 Hz max. (1 Hz default) - Capture time: at the start 27s, in operation 1s - Operating temperature: -40 ° C - + 85 ° C - separate GPS antenna (not included ): 18x18 mm - Size: 22x30x13 mm Code M0070 ✗ Out-of-Stock Price €14.90
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
Power Supply Transformer 220V AC/DC 2A 9V Power Supply Transformer 220V AC/DC 2A 9V features:- Input voltage: 100 ~ 240V 50Hz- Output voltage: DC 9V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0098 Available Price €3.99
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €7.95
Black Housing for Raspberry Pi 2, 3, Model B, B+ Black Housing for Raspberry Pi 2, 3, Model B, B+ features: - Black Case Shell Box - Housing for Raspberry Pi2, Pi3, B and B + - Color: Black - Made of ABS - Dimension: 95x 62x 26mm Code RA002 Available Price €2.70
USB to Micro USB On/Off Switch for Arduino Charger Cable It has an ON / OFF switch that will cut off power when you don't need it. USB to Micro USB On/Off Switch Arduino Charger Cable features: - Black color - Length: 150cm - Maximum current 1A Code K0054 Available Price €2.85
Camera IMX219-160 8MP 160° FOV - Compatible with NVIDIA Jetson Nano/ Xavier NX It is an 8-megapixel camera with a 160-degree field of view, equipped with a chip Sony IMX219. The camera is designed for NVIDIA Jetson Nano and NVIDIA Jetson Xavier NX development kits. Code SS046 Last items in stock Price €35.99
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.88
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
GPS Mini Station NEO-6M-0-001 with EEPROM SMA IPEX Ports It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip. The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed. Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC - Operating current: 45 mA - Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds - Navigation update: 5 Hz max. (1 Hz default) - Capture time: at the start 27s, in operation 1s - Operating temperature: -40 ° C - + 85 ° C - separate GPS antenna (not included ): 18x18 mm - Size: 22x30x13 mm Code M0070 ✗ Out-of-Stock Price €14.90
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
Power Supply Transformer 220V AC/DC 2A 9V Power Supply Transformer 220V AC/DC 2A 9V features:- Input voltage: 100 ~ 240V 50Hz- Output voltage: DC 9V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0098 Available Price €3.99