Computer power cable PC C14 black 1.8m

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Ideal to control the speed of DC motors.
Characteristic:
- Input voltage: 12-40VDC,
- Max continuous output current: 8A (peak current 10A),
- Control power: 0.01- 400W,
- Dimensions: 60x75x28mm,
- PWM frequency: 13kHz,
- Static current: 0.02 A (Standby),
- Adjustable duty cycle: 10% -100% ,
- It integrates a L7812CV TO-220 regulator,
- It incorporates a 10A fuse to protect the power circuit.
Note that the voltage applied to the motor will be the supply voltage applied to the circuit.

W1209 12V DC Thermostat Digital Temperature Controller Switch features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50 -110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measurement accuracy: 0.1 ° C
- Refresh rate: 0.5 s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Power of output: 10A relay
- Sensor probe: NTC waterproof sensor (10K 0.5%)
- Environmental requirements: -10 ~ 60 ° C Humidity 20% -85%
- Dimensions: 48 x 40 mm

Arduino UNO is the best board to start your experience with electronics and programming. If this is your first experience with the platform, UNO is the most robust board you can start with. UNO is the most widely used and documented board in the entire Arduino family. Its power ensures ATmega 328p microcontroller, the board is equipped with 14 digital pins, and 6 analog

24V Momentary LED Pushbutton Blue 16mm N/A NO features:
- Type of operation: momentary (automatic return)
- Contact switch: 1 NA (normally open)
- Max Switch Classification: 2A / 24VDC
- Body material: Stainless steel
- Button Material: Stainless steel
- Protection Classification: IP67 / IK08
- Operating temperature: -20C + 55C

Fan 12V 2x Cables 3D Reprap Printer features:
- For Prusa RepRap 3D Printer
- Voltage: 12V
- Consumption: 90mA - Speed: 7000rpm ± 10%
- Noise level: 25dB ± 10%
- Screw diameter: 3.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 28cm
- Dimensions: 30mm x 30mm x 10mm

Insulation Tapes PVC Red 20m x 19mm x 0.13mm features:
- PVC insulating tape with adhesive
- Thickness of 0.13 mm
- Measures 20m x 19mm
- Heat resistance: 80°C

This product is a 20x20mm extra strong adhesive base for nylon flanges 2.5mm up to 9mm wide. Its great fixing power prevents you from drilling.