Raspberry Pi

Expansion Board GPIO Shield 40 Raspberry Pi B+ Pin features:
- Shield module for Raspberry Pi 2 and Pi 3, B and B +

T-Cobbler Protoboard Extension Plate GPIO 40 Raspberry PI B+ Pin features:
- Shield expansion module for Raspberry Pi 2 and Pi 3, B and B +
- Dimension: 6 x 7.3x 1.9mm

T-Cobbler GPIO KIT + 40-pin Grey Flat Cable Pi B+ RPI 2 RPI 3 RPI Zero features:
- Shield to connect with breadboard
- Dimension: 6 x 7.3x 1.9mm
- Flat cable female / female 40 pins
- Total length: 25cm
- Quantity:
1x shield
1x flat cable

DS3231 Precision RTC Real Time Clock Module AVR ARM features:
- Can be used in projects of Arduino, Raspberry Pi, PIC, AVR
- Function compatible with the DS 3231
- Power supply voltage: +2.3 V to +5.5 V
- Temperature range: -40 ° C to + 85 ° C
- Low energy consumption
- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation
- Two alarm calendar
- Interface: I2C

2 Channel Relay Module 5V 10A for Arduino features:
- 5V relay module with 2 optocoupled channels
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- LED indicator: For each channel
- Dimensions: 40x 50mm

Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features:
- Interface type: USB
- Supports IEEE 802.11e draft 802.11n
- Supports USB 2.0, compatible with USB 1.1 and 1.2
- Support systems:
- Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux
- Operating distance: 91 meters indoors, 275 meters in open space
- Transfer rate: 150Mbps (downlink) and 150Mbps (uplink)
- Works with old Wireless-G and Wireless-B networks
- WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM
- Frequency range: 2.4 to 2.4835 GHz
- Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment
- Transmission mode: DSSS

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.

Pimeroni Unicorn HAT is one of the most popular and at the same time easiest to use Raspberry HATs in Pimoroni offering. It is featured with a matrix of 64 RGB LEDs powered directly through the Pi board. The applications of the HAT spread from just a simple games in the classroom up to color indications in your robot. All of this accessible in a really straight forward way and supported by a range of Python libraries available on github and officially issued by Pimeroni. The hat is compatible with all Raspbery boards given its universal 40 GPIO pinout

Pimeroni Display-O-Tron is one of the most popular and at the same time easiest to use HATs in Pimoroni offering. It is featured with 16x3 character LCD supporting a complete ASCII character set. The shield is powered directly through the Pi board. The board comes with multiple capactive touch pads on top of that. All functions of the shield are accessible in a really straight forward way and supported by a range of Python libraries available on github and officially issued by Pimoroni. The hat is compatible with all Raspbery boards given its universal 40 GPIO pinout

Pimeroni Unicorn HAT HD is one of the most popular and at the same time easiest to use Raspberry HATs in Pimoroni offering. Compared to the Unicorn HAT it is equiped with twice as many LEDs in a row and a column giving a matrix of 256 LEDS! All of this accessible in a really straight forward way and supported by a range of Python libraries available on github and officially issued by Pimeroni. The hat is compatible with all Raspbery boards given its universal 40 GPIO pinout

The Pimeroni Automation HAT (PIM213) is a great solution for home automation. The controller board includes relays, powered outputs and buffered inputs up to 24V as well as analog channels. Set of LEDs showing the current state of each of the channels. So if you need to get a light automation or garden sprinkling phasing set in place, this is the board just for you

Can't stand to run out of pins in your Raspberry Pi? You have a cool new accessory but there's no way to plug it in? If you answered yes to any of the above, then this pHAT could be just for you. This piece has 6 sets of 40 GPIOS - one for your Pi and the rest (5) for your collection of HATs that you might want to plug in at the same time. Use it for a specific project or just to play with several HATs at once.  

16 servo motors with one board seems impossible? With this board not only it isn´t impossible, but it even seems easy. Additionally, you won´t need to sacrifice any of your valuable GPIOs as the HAT connects directly via I2C. Additionally, you have a serial terminal connection at your disposal.

You can supply the power to the board through your Pi or directly if you are going for larger servos and would need a separate source of power. Simply scrap a small blob of solder on the isolation jumper.

You are looking for an easy way to program a microcontroller in your Arduino. It has never been easier - with this board you can do it in the record speed with support or Raspberry (or without for that matter, as the HAT works on the standalone basis as well). It was first developed as an in-house solution for Sparkfun production, and for its quality and usefulness ended up in mass production with a solid fan following.

The board includes several handy features ranging from the capacitive touch button for a standalone mode to launch programming, LEDs indicating the status of the program upload as well as some whiteboard labels to keep track of your projects.

QWIIC is a connection standard developed by Sparkfun enabling a quick an easy connection of peripherals without a need to solder pins, without any mismatches due to polarized connector. And on top of that you can "daisy chain" them! 

This hat pretty much opens the whole QWIIC universe in front of your Pi. It features 4 QWIIC ports all on the same I2C bus (GND, 3.3V, SDA, and SCL).

A universal  2x20 GPIO makes it compatible with all Raspberry Pi boards, as well as Google Coral and Jetson Nano.

Note:  For a secure connection in some applications, you'll need to add a pair of 1x20 stackable headers to extend the pins to your cart.

Pimoroni Fan is the best you can do for your new Raspberry 4! It is a well known fact, Raspberries can get hot. Even though, there are plenty of solutions to that, you will find no better than this Pimoroni Fan. It is a no-solder device, hence you can put it on and off as you wish

Sense HAT is your absolute classic used for a well-known and popular Astro Pi projects. It features set of sensors (Pressure, humidity, IMU and temperature) and a great 8x8 LED screen. It is a full set for your Raspberry - you can both measure your projects environment, display it on the screen as well as manouver and input data with joystick and buttons included on the HAT.

SparkFun Hamburger speaker is a high quality speaker in a small form and with even smaller price. You wouldn't believe you can get a quality product for less than 7€, right? Well, we couldn't believe that as well, but SparkFun makes that possible.

The Qwiic HAT is an absolute basic of Qwiic system for Raspberry. It enables a quick and efficient connection of an sensor to your Raspberry over I2C bus (GND, 3.3 V, SDA and SCL). As Qwiic enables daisy chaining of components, you can pretty much install as many sensors on the Qwiic HAT as you want. On top of that it fits perfectly Pi Tin enclosure from SparkFun enabling connection while in case.

This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds

It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

The kit includes 20 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes.

The kit includes 30 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes.