Transistor heat sink with TO-220/TIP120 box

Rocker Switch 3A 250V On/Off SPST features:
- AC 250V 3A 2 Pin ON/OFF I/O SPST Snap in mini oscillating switch
- Rocker switch; Type: On/Off (SPST)
- Control on and off SPST and 2 terminals
- Voltage and Current: AC250V, 3A
- Overall size: ~ 1.5 x 1 x 1.7 cm/0.6"x 0.4" x 0.7 "(L*W*H)
- Mounting hole size: 1.35 x 0.8 cm/0.53"x 0.315" (L*W)
- Black

Premium Bobina para Impresora 3D

It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector.

LED Diode Assortment Kit 15 pcs 5mm red, green, yellow features:
- Lens color: red, green, yellow - diffuse
- Size: 5mm
- Operating current: 20mA
- Voltage (red) 1,8V-2,3V
- Voltage (green) 3,2V-3,4V
- Voltage (yellow) 1,8V-2,3V
- Anode (A): Positive (long leg): 28mm
- Catode (K): Negative (short leg): 25mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: +260ºC
- Quantity: 30 units
*5x red
*5x green
*5x yellow

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

Resistor 1K Ohm 5% 0,25W 1/4W features:
-1K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Characteristic:
- Output Type: Fixed
- Voltage Output: 5V
- Manufacturer: ST Microelectronics
- Output Current: 100mA
- Input voltage max.: 30V
- Input voltage min.: 7V
- Operating temperature: 0ºC to + 70ºC
- Encapsulated: TO-92
- Polarity: Positive
- Tolerance output voltage: 5%
- Quantity: 1 unit

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328