Arduino Uno R3 Arduino UNO is the best board to start your experience with electronics and programming. If this is your first experience with the platform, UNO is the most robust board you can start with. UNO is the most widely used and documented board in the entire Arduino family. Its power ensures ATmega 328p microcontroller, the board is equipped with 14 digital pins, and 6 analog Code BAR66 Available Price €23.99
Tuya Smart ZigBee 3.0 Ethernet Gateway - Control unit: The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices. Code WT007 ✗ Out-of-Stock Price €28.90
Magnetic sensor switch for windows/doors 14X27mm adhesive This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0275 Backorder Price €1.99
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.49
Temperature Sensor Module MLX90614ESF-BCC GY-906 The GY-906 BCC is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, accuracy within 5 cm is approximately 0.5 degrees higher Code S0146 Available Price €17.50
Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.39
MQ-7 Carbon Monoxide Sensor Module MQ-7 Carbon Monoxide Sensor Module. The sensor detects the concentration of CO (carbon monoxide) and flammable gases. It has a goldpin connector raster 2.54 mm. It is powered by 5 V. It has digital and analogue outputs, which makes it compatible with most runtime modules including Arduino. Code S0031 Available Price €2.95
Seeed Grove Base kit for Raspberry Pi The Grove Base Kit for Raspberry is all you need to start playing and making with your Raspberry Pi board. It is compatible with boards Pi 3 and Pi 4 and includes 8 basic sensors, a display and a motor. All of that on the grove connectors making it a seamless experience. Code SS006 Last items in stock Regular price €65.99 -€6.00 Price €59.99
F50-12V 10W DC Micro Hydro Generator Mini electricity generator, built base on a turbine and an electric generator that converts kinetic energy into electricity. The generator output is rectified and regulated for a maximum of 12V. Please note -if we want to generate more current, the turbine will oppose the greater resistance to the flow of water, and the voltage may drop if the water flow is not sufficient. This generator is made of plastic and the turbine is totally isolated from the generator and rectifier, the outputs are 1/2 "usually found in domestic pipes. Code M0211 Last items in stock Regular price €11.95 -€1.50 Price €10.45
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
Tuya Smart ZigBee 3.0 Ethernet Gateway - Control unit: The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices. Code WT007 ✗ Out-of-Stock Price €28.90
Magnetic sensor switch for windows/doors 14X27mm adhesive This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0275 Backorder Price €1.99
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.49
Temperature Sensor Module MLX90614ESF-BCC GY-906 The GY-906 BCC is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, accuracy within 5 cm is approximately 0.5 degrees higher Code S0146 Available Price €17.50
Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.39
MQ-7 Carbon Monoxide Sensor Module MQ-7 Carbon Monoxide Sensor Module. The sensor detects the concentration of CO (carbon monoxide) and flammable gases. It has a goldpin connector raster 2.54 mm. It is powered by 5 V. It has digital and analogue outputs, which makes it compatible with most runtime modules including Arduino. Code S0031 Available Price €2.95
Seeed Grove Base kit for Raspberry Pi The Grove Base Kit for Raspberry is all you need to start playing and making with your Raspberry Pi board. It is compatible with boards Pi 3 and Pi 4 and includes 8 basic sensors, a display and a motor. All of that on the grove connectors making it a seamless experience. Code SS006 Last items in stock Regular price €65.99 -€6.00 Price €59.99
F50-12V 10W DC Micro Hydro Generator Mini electricity generator, built base on a turbine and an electric generator that converts kinetic energy into electricity. The generator output is rectified and regulated for a maximum of 12V. Please note -if we want to generate more current, the turbine will oppose the greater resistance to the flow of water, and the voltage may drop if the water flow is not sufficient. This generator is made of plastic and the turbine is totally isolated from the generator and rectifier, the outputs are 1/2 "usually found in domestic pipes. Code M0211 Last items in stock Regular price €11.95 -€1.50 Price €10.45
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39