NTC thermistor 100K 3950 1m RepRap cable

This module is a passive buzzer, a low trigger level alarm for Arduino. It emits different sounds at various frequencies. The buzzer sounds when the I / O port input is low level. 

Characteristic: - Supports up to 280ºC
- Electrical and antistatic insulation
- Resistant to acid and alkaline products
- Resistant to solvent
- Adhesive
- Length Approx: 26m
- Known as Kapton polyamide tape
- Product for welding jobs where it is necessary to protect some component from heat

This switch can be used for development projects and for the industry. All metal parts are not oxidized, the insulation material is of high quality.
Its pins protected by an anti oxidant makes welding much easier. Switch On/On 6-pin 6A SPDT features:
- Type: Latch SPDT
- Material: Plastic, metal
- Maximum operating current and voltage: 3A / 250V, 6A / 125V
- Number of pins: 6
- Pin size: 4.5x2 mm
- Type of current: AC
- Pins to be welded
- Switch action: 2 positions On/On
- Size: 13.2x12.7x33.3mm

Nozzle Head 0.4 1.75mm MK8 3D Printer Extruder features:
- MK8 Precision Nozzle: 0.4mm
- Material: Copper
- Size: 13mm x 6mm
- Suitable for Filament: 1.75mm
- Quantity: 1 unit

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

Heater Block MK8 NTC 3950 Nozzle 0.4mm 1.75mm features:
- 3D Printer Extruder
- 0.4mm Nozzle
- 100k 3950 NTC thermistor with cable
- MK8 heater block with 12v / 40W thermal ceramic resistance with cable
- 1.75mm filament stud M6x30mm

Load cell Load Cell Weight Sensor 2kg features:
- Load cell to measure weight up to 2kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 2kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65