Resistor 330 Ohm 5% 0,25W 1/4W

LED Diode Assortment Kit 15 pcs 5mm red, green, yellow features:
- Lens color: red, green, yellow - diffuse
- Size: 5mm
- Operating current: 20mA
- Voltage (red) 1,8V-2,3V
- Voltage (green) 3,2V-3,4V
- Voltage (yellow) 1,8V-2,3V
- Anode (A): Positive (long leg): 28mm
- Catode (K): Negative (short leg): 25mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: +260ºC
- Quantity: 30 units
*5x red
*5x green
*5x yellow

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 10.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

Ideal for building a car with obstacle detector, light follower
Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Mega2560, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

Characteristic: -Conductor: solid wire, tinned copper
-Insulation: PVC
-Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007
-Number of conductors: 22AWG, 1x0.35mm2
-Outer diameter: 1.6mm

Ideal to power your Arduino board through the power input.
9v Battery Adapter Connector 6F22 with Cable features: