Pulley GT2 40 Teeth 6mm Aluminium 3D Printer Reprap CNC

Sensor Module GUVA-S12SD UV features:
- The module based on the Schottky-type photodiode - applicable to the optical mode
- This is a " true "UV sensor instead of calibrated light sensor
- It has high sensitivity, high stability, good linearity
- Power supply: 2.5V - 5V
- Analog output
- Captured wavelength: 240-370nm
- Ultra low power consumption
- Meteorological applications, skin care, industrial UV level measurement
- PCB dimensions: 11x27mm

3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features:

- Based on the LM2596S-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 1.25v - 32v DC (adjustable)
- Voltage of Input: 3.2v - 35v DC
- Max Output Current: 3A (with heat sink)
- Ripple at output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 2.5%
- Operating Temperature: -40ºC to + 85ºC
- Measurements 43x 21x 14 mm

Tower Pro Micro Servo 9g SG90 360 degree features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

Low Signal High Speed ​​Switching.
These diodes are widely used to multiplex signals, such as buttons or digital inputs Characteristic:
- Reverse voltage: 100V,
- Forward voltage drop: 1V to 10mA,
- Forward direct current: 200mA,
- Maximum overvoltage current: 4A,
- Dissipated power: 500mW,
- Recovery time: 4ns,
- Configuration: Simple,
- Package: DO-35,
- Quantity: 30 units .

GT2 Strap Kit 2m + 2x Pulley GT2 16 Teeth 6mm features:
- Number of teeth: 16
- Pitch: 2mm
- Material: aluminum alloy
- Outside diameter: 13mm
- Inner hole: 5mm
- Use with strap: 6mm
- GT2 strap made of rubber with fiberglass reinforced
- Length 2m
- Width: 6mm
- Belt height: 1.38 mm Ideal to fix on the axis of the motors of your 3D printer.

Screen OLED 0.96" B 128x64 Yellow-Blue SPI/I2C features:
- Oled 0.96 "128 * 64 pixel display
- One yellow line and 3 blue lines
- Drive IC model SDD1306
- Power supply: 3V-5.5V
- View angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption 0.08W
- Temperature usage: -20 to 70 ºC
- PCB board dimension: 32 x 32 mm
- OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption of energy.

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Mega2560, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328