5x Push Switch Button B3F Omron Blue Key 12mm 5x Push Switch Button B3F Omron Blue Key 12mm features:- 5x Push Buttons B3F Omron Key- Maximum current: 50 mA- Tension DC: 24V- Operating force: 1.27N- Switch terminals: weldable- Contact: SPST-NO- Contact resistance: 100M Ohm- Type of action: Superficial- Measures: 12x12x7.3mm Code K0074 Available Price €0.21
NTC thermistor 100K 3950 1m RepRap cable Sensor used to measure the temperature of the hotend or hot bed of your 3D printer Characteristic: - NTC Thermistor 100 K 3950 - Impedance: 100 K (25º of Temperature) - Accuracy: 1% - Sensor Diameter: 1.8 mm - Cable Length: 1 m - Cable: AWM UL 3398 150 ° C 300V - Ready to be installed and used. Fully insulated - Designed to withstand the high temperatures of extrusion of plastics such as PLA and ABS Code I0018 Available Price €1.10
10x Tactile Tact Push Button Switch 6x6x8mm 10x Tactile Tact Push Button Switch 6x6x8mm features:- Tactile Push Tact Switch mini electronic Arduino pushbutton- Measures: 6x6x8mm- Quantity: 10 units Code K0076 Available Price €0.15
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.90
Potentiometer B1K Linear Potentiometer B1K Linear features: -1k OHM kΩ - linear potentiometer 1k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0065 Available Price €0.99
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €9.90
Heat Shrinkable Tube 5 Colors 3 Meters Package Heat Shrinkable Tube 5 Colors 3 Meters Package features: - Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas. - These heat shrink tubes are very flexible and of high quality. Made in EU - Different sizes of 20 cm each are delivered: * 1,6mm: black, brown, red, yellow, orange * 2,4mm: black, brown , red, yellow, blue * 3,2mm: black, brown, red, yellow, blue - Quantity: 15 units - Material: polyolefin - Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter) - Minimum shrinkage temperature: 115 ° C maximum 200 ° C Code K0047 Available Price €1.95
10m Rigid cable, 22AWG yellow PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0226 Available Price €3.89
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Regular price €8.95 -€2.00 Price €6.95
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €5.50
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Regular price €8.95 -€2.00 Price €6.95
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €5.50
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98