Magnet Cylindrical Disc Neodymium Ferrite 3x6mm

Velostat or Linqstat film of pressure sensitive material ideal for DIY projects on Arduino, Raspberry or other platforms. When folded or creased it reduces its resistance allowing for flexible sensors.

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on

LED Diode Assortment Kit 50x Red Green Yellow Blue White features:
  
- Lens color: Red, green, yellow, blue - diffuse, light white
- Size: 5 mm
- Operating current: 20mA
- Voltage (red) 1.8V-2.3V
- Voltage (green) 3.2V-3.4V
- Voltage (yellow) 1.8V-2.3V
- Voltage (blue) 3.0V-3.2V
- Voltage (white) 3.2V - 3.4V
- Anode (A): Positive (long leg): 17mm
- Cathode (K): Negative (shorter leg): 15 mm
- Operating temperature: -25ºC / 80ºC
- Welding temperature: + 260ºC
- Quantity: - 50 units
                  - 10x red
                  - 10x green
                  - 10x yellow
                  - 10x blue
                  - 10x white

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Buzzer alarm to convert electrical signals into intermittent acoustic signals in robotic devices and Arduino projects

A buzzer with a pulsating tone generator, after connecting the supply voltage (DC) in the range of 3V -24V, the buzzer generates an intermittent signal with a frequency of approximately 1 Hz. Application example: as a reverse alarm system for a car. 

Tower Pro Micro Servo 9g SG90 360 degree features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

40x Male to male cables 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont male connectors on both ends
- Compatible with 2.54mm female connectors
- High quality and good working condition
- Easy to install and use

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.