T8 Spindle 50cm with Trapezoid Nut R2

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Mini Soldering Iron Stand features:
- Mini Holder for tin soldering iron
- Dimensions: 65x 40mm

This BLtouch sensor is an automatic leveling sensor for 3D printers that can accurately measure the inclination of your printing surface.
It can greatly improve the printing precision of your 3D printer.
Its features: are simple, smart and precise.
It could work with almost any type of bedding, such as glass, wood , metals, etc. 3DTouch's main functions and controls are the same as most automatic bed leveling sensors, consisting of an RC servo and a micro switch.

Self-leveling sensor BLtouch 3D printer features:
- Supply voltage: 5V.
- Supply current: 15mA
- Max. Current: 300mA
- Len3Dh cable: 150mm
- Wiring:
- 3 pins: Brown (-, GND) Red (+ 5V) Orange (control signal)

10x Female-Female Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have female header contacts at either end
-Compatible with male connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

10x Male-Male Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have male header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 28.5 kg/cm. Comes with a 50 cm cable. We have the best stepper motors at the best prices! Perfect for CNC machines!