Dupont Connector 2.54mm Male Dupont Connector 2.54mm Male features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0111 Available Price €1.81
Pulley GT2 20 Teeth 5mm Aluminium Pulley 3D Printer Pulley GT2 20 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 20 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 18mm - Inner hole: 5mm - Use with strap: 6mm and 6.35mm - Ideal to fix on the axis of the motors of your 3D printer Code I0031 Available Price €1.48
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.82
Load Cell Weight Sensor 2kg Load cell Load Cell Weight Sensor 2kg features: - Load cell to measure weight up to 2kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 2kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0125 Available Regular price €2.47 -€0.99 Price €1.48
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €2.88
Green Propeller for Micro Motor 3V 5 6V DC DIY for Arduino Green Propeller for Micro Motor 3V 5 6V DC DIY Arduino. Code R0083 Available Price €0.65
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.31 -€0.39 Price €1.92
Flexible Coupler 5mm/8mm Z-axis CNC 3D Printer Flexible Coupler 5mm/8mm Z-axis CNC 3D Printer features: - High quality flexible aluminum coupler with which you can connect Nema 17, 5mm stepper motors to an 8 mm threaded rod - They incorporate 4 captive screws so that you can perfectly fix the couplings to the rod - Material: Aluminum alloy - Coupler height (L): 25 mm - Outside diameter: 18mm - Shaft diameter: 5mm / 8mm Code I0064 Available Price €1.31
Lead Screw with Trapezoidal Nut T8 50cm L8 Lead screw and stainless steel screw set with KFL08 T8-800 for 3D printer. Its shaft coupling diameter is 8mm with pitch of 2mm and has a length of 800mm Lead Screw with Trapezoidal Nut T8 50cm L8 features: - Type: Trapezoidal screw- Diameter: 8mm- Toothing distance: 2mm - Rotation total: 8mm - Lengths: 500 mm Kit contents: - Nut 1 unit- Spindle 1 unit Code I0167 Available Regular price €11.15 -€2.00 Price €9.15
T8 Spindle 80cm with Trapezoid Nut R2 T8 Spindle 80cm with Trapezoid Nut R2 features: - Type: Trapezoidal Screw - Diameter: 8mm - Tooth distance: 2mm - Lengths: 800 mm - Quantity: * Nut 1 unit * Spindle 1 unit Code I0113 ✗ Out-of-Stock Price €9.88
T8 R2 50cm Spindle Kit with Bearing Support, Nut and Coupler T8 R2 50cm Spindle Kit with Bearing Support, Nut and Coupler features: - With bearing bracket, nut, coupler for CNC 3D Printer - T8 spindle - Type: Trapezoidal screw * Diameter: 8mm * Tooth distance: 2mm * Lengths: 500 mm - Coupler 5mm / 8mm * Material: Aluminum alloy Code I0114 ✗ Out-of-Stock Price €15.66
Anti Backlash Spring Loaded Nut for Trapezoidal Screw L8 This type of spring nut is suitable only for type B trapezoidal screws with a pitch of 2 mm that give a complete revolution of 8 mmAnti Backlash Spring Loaded Nut for Trapezoidal Screw L8 features:- Material: brass and steel spring- Complete revolution: 8 mm- Diameter: 22 mm- Length: 43 mm- Each anti-rebound nut included large nut, spring and small nut Code I0150 Available Price €3.26
Lead Screw with Trapezoidal Nut T8 80cm L8 Lead screw and stainless steel screw set with KFL08 T8-800 for 3D printer. Its shaft coupling diameter is 8mm with pitch of 2mm and has a length of 800mm Lead Screw with Trapezoidal Nut T8 80cm L8 features: - Type: Trapezoidal screw- Diameter: 8mm- Toothing distance: 2mm - Rotation total: 8mm - Lengths: 800 mm Kit contents: - Nut 1 unit- Spindle 1 unit Code I0148 Last items in stock Price €12.36
T8 Spindle 50cm with Trapezoid Nut R2 T8 Spindle 50cm with Trapezoid Nut R2 features: - Type: Trapezoidal Screw - Diameter: 8mm - Tooth distance: 2mm - Lengths: 500 mm - Quantity: * Nut 1 unit * Spindle 1 unit Code I0100 Available Price €8.67
Lead Screw with Trapezoidal Nut T8 50cm L8 Lead screw and stainless steel screw set with KFL08 T8-800 for 3D printer. Its shaft coupling diameter is 8mm with pitch of 2mm and has a length of 800mm Lead Screw with Trapezoidal Nut T8 50cm L8 features: - Type: Trapezoidal screw- Diameter: 8mm- Toothing distance: 2mm - Rotation total: 8mm - Lengths: 500 mm Kit contents: - Nut 1 unit- Spindle 1 unit Code I0167 Available Regular price €11.15 -€2.00 Price €9.15
T8 Spindle 80cm with Trapezoid Nut R2 T8 Spindle 80cm with Trapezoid Nut R2 features: - Type: Trapezoidal Screw - Diameter: 8mm - Tooth distance: 2mm - Lengths: 800 mm - Quantity: * Nut 1 unit * Spindle 1 unit Code I0113 ✗ Out-of-Stock Price €9.88
T8 R2 50cm Spindle Kit with Bearing Support, Nut and Coupler T8 R2 50cm Spindle Kit with Bearing Support, Nut and Coupler features: - With bearing bracket, nut, coupler for CNC 3D Printer - T8 spindle - Type: Trapezoidal screw * Diameter: 8mm * Tooth distance: 2mm * Lengths: 500 mm - Coupler 5mm / 8mm * Material: Aluminum alloy Code I0114 ✗ Out-of-Stock Price €15.66
Anti Backlash Spring Loaded Nut for Trapezoidal Screw L8 This type of spring nut is suitable only for type B trapezoidal screws with a pitch of 2 mm that give a complete revolution of 8 mmAnti Backlash Spring Loaded Nut for Trapezoidal Screw L8 features:- Material: brass and steel spring- Complete revolution: 8 mm- Diameter: 22 mm- Length: 43 mm- Each anti-rebound nut included large nut, spring and small nut Code I0150 Available Price €3.26
Lead Screw with Trapezoidal Nut T8 80cm L8 Lead screw and stainless steel screw set with KFL08 T8-800 for 3D printer. Its shaft coupling diameter is 8mm with pitch of 2mm and has a length of 800mm Lead Screw with Trapezoidal Nut T8 80cm L8 features: - Type: Trapezoidal screw- Diameter: 8mm- Toothing distance: 2mm - Rotation total: 8mm - Lengths: 800 mm Kit contents: - Nut 1 unit- Spindle 1 unit Code I0148 Last items in stock Price €12.36
T8 Spindle 50cm with Trapezoid Nut R2 T8 Spindle 50cm with Trapezoid Nut R2 features: - Type: Trapezoidal Screw - Diameter: 8mm - Tooth distance: 2mm - Lengths: 500 mm - Quantity: * Nut 1 unit * Spindle 1 unit Code I0100 Available Price €8.67