Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
MQ-6 Gas Methane Sensor Module for Arduino MQ-6 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-6 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm- 10000ppm LPG, LNG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0030 Available Price €2.59
40x Female-Female Cable 10cm 40x Female-Female Cable 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont female connectors on both ends - Compatible with 2.54mm male connectors - High quality and good working conditions - Easy to install and use Code K1005 Available Price €1.99
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€2.00 Price €4.49
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.95
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.75
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €3.49
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Last items in stock Price €7.95
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €7.89 -€1.00 Price €6.89
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.95
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.95
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €3.49
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Last items in stock Price €7.95
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €7.89 -€1.00 Price €6.89
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.95
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.95