Solar panel DIY 6V 1.1W 200mA

Dupont Connector 2.54mm Female features:
- Connector for soldering or crimping
- Lot 100 units
- Ideal for your projects electronic, arduino, but can also be used with other microcontrollers

Blue sponge to clean the tip of your soldering iron to the tin.
Blue cleaning sponge for soldering iron tip with pre-cut circle at the center features:
- Circle diameter 17mm precut to the center of the sponge,
- Size: 55x55mm,
- Material: sponge,
- Color: blue,
- Quantity: 1.

- This module includes PA preamplifier and LNA (Low-noise amplifier)
- Comes with the SMA antenna for 2.4GHz (2dB)
- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer
- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features:
* Based on chip NRF24L01 +
* Free band: 2.4GHz ISM
* Speed: 250kbps, 1Mbps, 2Mbps
* Work current
- Reception: 45 mA
- Transmission: 115 mA (4.2uA -sleep mode)
* Receiving sensitivity:
-104dB 250kbps
- 95dB 1Mbps
- 92dB 2Mbps
* SPI interface

TP4056 Module Lithium Battery Charger with Protection features:
- TP4056 Li-Ion Micro USB Charger
- Upgraded version of previous TP4056
- Micro USB connection to charge directly from the PC
- Ideal for 18650 batteries
- Based on the TC4056A regulator
- Input Voltage: 4.5V - 5.5V DC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Overvoltage protection 4.2V
- Over discharge protection 2.4V
- LED indicator: charging blue, charging red
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Overcurrent protection: 3A
- Measurements 26 x 19 x 5 mm
- Possibility of current change through Rprog

Super capacious 9V battery made in Li-ion technology, direct charging possible via micro USB port!

tested capacity - real capacity - min. 500 mAh, battery precharged to max. 30%.

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

This module works under the characteristics of the integrated ISD1820 and allows you to make recordings of multiple messages or the reproduction thereof, it performs a non-volatile storage. Voice Recording and Reproduction Module ISD1820 features:
- Working voltage: 2.4 - 5.5 VDC
- Model: I073103
- Voice Recorder Chip ISD1820
- Automatic ignition mode dwon
cording duration: 8-20 seconds
- Manual or Automatic Control with an MCU
- With internal audio amplifier, this board can drive 8 ohm 0.5W speaker directly
- Includes a microphone on board to record directly
- The sampling frequency and duration can be different if a single module resistance is changed
- High quality, restored natural voice, can be used as a speaker module

Micro Servo Compatible with MG90S features:
- Operating voltage: 4.8Vdc (5V) or 6Vdc
- Torque: 1.80 kg / cm at 4.8V and 2.20kg / cm at 6V
- Speed: 0.1seconds / 60º at 4.8V and 0.8 seconds / 60º at 6V
- Gear type: metallic
- Turning width: 180º
- Temperature working: from -30 to 60 ºC
- 3 plastic propellers / arms
- Fixing screws
- Size: 22.6 x 11.8 x 31 mm
- Weight: 13.4 gr