Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
40x Female-Female Cable 10cm 40x Female-Female Cable 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont female connectors on both ends - Compatible with 2.54mm male connectors - High quality and good working conditions - Easy to install and use Code K1005 Available Price €1.99
Wireless Remote Control + 4 Channel Receiver Wireless Remote Control + 4 Channel Receiver features: Remote Control: - Operating voltage: DC12V (battery included)- Operating current: 10mA @> Code W0001 Available Price €4.95
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
Resistors Kit 5% 0,25W 1/4W Resistors Kit 5% 0,25W 1/4W features: -10 pcs - 100 Ohm-10 pcs - 220 Ohm-10 pcs - 1,0k Ohm-10 pcs - 2,2k Ohm-10 pcs - 4,7k Ohm-10 pcs - 10k Ohm-10 pcs - 100k Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0071 Available Price €2.80
10x Rectifier Diode 1N5408 3A 1000V 10x Rectifier Diode 1N5408 3A 1000V features:- Reverse voltage: 1000V- Direct voltage drop: 1.2V- Direct direct current: 3A- Configuration: Simple- Encapsulated: DO-201AD- Quantity: 5 units Code T0017 Available Price €0.13
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Battery Holder 6x AA LR06 Ideal to power your Arduino board.Battery Holder 6x AA LR06 features:- Cable 12cm long,- Measures 90x 55x 15mm,- Max 50mm pile length,- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7). Code PP007 Available Price €1.75
Red Laser Line Generator 650nm 20mW Red Laser Line Generator 650nm 20mW features:- Module Focus Adjustable Laser Head 3V- Type: Red laser diode- Type of laser: Line- Adjustable Focus- Wavelength: 650nm- Output power: 20mW- Operating voltage: 3V-4V- Operating intensity: <40mA- Operating temperature: -30ºC to 60ºC- Dimensions of the emitter: Φ12x35mm- Cable length: 130mm Code M0050 Available Regular price €9.49 -€1.00 Price €8.49
LED 5mm RGB Common Anode LED 5mm RGB 4 Pin anode commun with clear water lens. Code P0019 Available Price €0.21
Red Laser Line Module Generator 650nm 5mW Red Laser Line Module Generator 650nm 5mW features: - Type: red laser diode- Type of laser: line- Adjustable Focus- Wavelength: 650nm- Output power: 5mW- Operating voltage: 4.5-5V- Operating intensity: <40mA- Operating temperature: -30ºC to 60ºC- Dimensions of the emitter: Φ12x35mm- Cable length: 130 mm Code M0039 Available Price €3.95
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €15.95 -15% Price €13.56
20x Zener Diode BZX55C3V6 3.6V 500mW DO-35 0.5W 3V6 20x Zener Diode BZX55C3V6 3.6V 500mW DO-35 0.5W 3V6 features:-Zerner voltage: 3.6V-Tolerance: 5%-Power dissipated: 500mW-Enter Zener: 85 Ohm-Configuration: Simple-Encapsulated: DO-35-Temperature of work: -65C to 175C-Quantity: 20 units Code T0025 Available Price €0.10
LED Diode COB 3W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0144 Available Price €1.32
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
10x Zener Diode BZX85C4V7 4.7V 1.3W DO-41 1300mW 4V7 10x Zener Diode BZX85C4V7 4.7V 1.3W DO-41 1300mW 4V7 features:-Zener voltage: 4.7V-Tolerance: 5%-Power dissipated: 1300mW-Enter Zener: 13 Ohm-Configuration: Simple-Encapsulated: DO-41-Temperature of work: -65C to 200C-Quantity: 10 units Code T0032 Available Price €0.20
10x Zener Diode BZX85C4V3 4.3V 1.3W DO-41 1300mW 4V3 10x Zener Diode BZX85C4V3 4.3V 1.3W DO-41 1300mW 4V3 features:-Zerner voltage: 4.3V-Tolerance: 5%-Power dissipated: 1300mW-Enter Zener: 13 Ohm-Configuration: Simple-Encapsulated: DO-41-Temperature of work: -65C to 200C-Quantity: 10 units Code T0031 Available Price €0.20
LED diode 3mm 12V DC Light blue with 20cm cable Through-hole LED for 12V DC with black and red 20cm cable. Diode type: with cable LED lens type: Clear Direct diode voltage: 12V LED colour: light blue The distinguishing feature: 12 V LED with 20 cm RoHS cable LED size: 3 mm Code K0276 Backorder Price €0.49
Red Laser Line Generator 650nm 20mW Red Laser Line Generator 650nm 20mW features:- Module Focus Adjustable Laser Head 3V- Type: Red laser diode- Type of laser: Line- Adjustable Focus- Wavelength: 650nm- Output power: 20mW- Operating voltage: 3V-4V- Operating intensity: <40mA- Operating temperature: -30ºC to 60ºC- Dimensions of the emitter: Φ12x35mm- Cable length: 130mm Code M0050 Available Regular price €9.49 -€1.00 Price €8.49
LED 5mm RGB Common Anode LED 5mm RGB 4 Pin anode commun with clear water lens. Code P0019 Available Price €0.21
Red Laser Line Module Generator 650nm 5mW Red Laser Line Module Generator 650nm 5mW features: - Type: red laser diode- Type of laser: line- Adjustable Focus- Wavelength: 650nm- Output power: 5mW- Operating voltage: 4.5-5V- Operating intensity: <40mA- Operating temperature: -30ºC to 60ºC- Dimensions of the emitter: Φ12x35mm- Cable length: 130 mm Code M0039 Available Price €3.95
LED Lighting Chain WS2811 Pixels Digital Addressable RGB 50LED 5V IP68 This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually. WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background Easy programming with Arduino, ESP32, ESP8266, etc. Code P0164 Available Regular price €15.95 -15% Price €13.56
20x Zener Diode BZX55C3V6 3.6V 500mW DO-35 0.5W 3V6 20x Zener Diode BZX55C3V6 3.6V 500mW DO-35 0.5W 3V6 features:-Zerner voltage: 3.6V-Tolerance: 5%-Power dissipated: 500mW-Enter Zener: 85 Ohm-Configuration: Simple-Encapsulated: DO-35-Temperature of work: -65C to 175C-Quantity: 20 units Code T0025 Available Price €0.10
LED Diode COB 3W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0144 Available Price €1.32
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
10x Zener Diode BZX85C4V7 4.7V 1.3W DO-41 1300mW 4V7 10x Zener Diode BZX85C4V7 4.7V 1.3W DO-41 1300mW 4V7 features:-Zener voltage: 4.7V-Tolerance: 5%-Power dissipated: 1300mW-Enter Zener: 13 Ohm-Configuration: Simple-Encapsulated: DO-41-Temperature of work: -65C to 200C-Quantity: 10 units Code T0032 Available Price €0.20
10x Zener Diode BZX85C4V3 4.3V 1.3W DO-41 1300mW 4V3 10x Zener Diode BZX85C4V3 4.3V 1.3W DO-41 1300mW 4V3 features:-Zerner voltage: 4.3V-Tolerance: 5%-Power dissipated: 1300mW-Enter Zener: 13 Ohm-Configuration: Simple-Encapsulated: DO-41-Temperature of work: -65C to 200C-Quantity: 10 units Code T0031 Available Price €0.20
LED diode 3mm 12V DC Light blue with 20cm cable Through-hole LED for 12V DC with black and red 20cm cable. Diode type: with cable LED lens type: Clear Direct diode voltage: 12V LED colour: light blue The distinguishing feature: 12 V LED with 20 cm RoHS cable LED size: 3 mm Code K0276 Backorder Price €0.49