Heat shrink tubing set 10cm 100unds
  • Heat shrink tubing set 10cm 100unds

Heat shrink tubing set 10cm 100unds

K0596

High quality and very flexible heat shrink tubing. Available in different sizes (1.5mm, 2.5mm, 4mm, 6mm, 10mm and 13mm) in six colours (black, white, red, yellow, yellow, green, blue), each 10 cm long.

OEM
5903802656350
Add to wish list

High quality, highly flexible heat shrink tubing. 

The heat shrink tubing is used for connecting electrical cables, insulating resistor and capacitor points, marking and protecting electrical cables, protecting metal rods or tubes against corrosion and protecting antennas. The kit is supplied in a handy transparent case.

The kit includes the following 100 mm long heat shrink tubing:

  • 1.5 mm tube black 30 pcs.
  • 2.5 mm tube yellow 30 pcs.
  • 4 mm tube red 20 pcs.
  • 6 mm tube green 10 pcs.
  • 10 mm tube blue 6 pcs.
  • 13 mm tube white 4 pcs.

Heat Shrinkable features:

  • - Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
  • - These heat shrink tubes are very flexible and of high quality. 
  • - Quantity: 100 units
  • - Material: polyolefin
  • - Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
  • - Minimum shrinkage temperature: 115 ° C maximum 200 ° C
  • - Maximum operating temperature: -55 ° C to + 105 ° C
  • - Tensile strength: 12 MPa
  • - Dielectric strength: 16 kV / mm
  • - Manufacturing specification: Reach, RoHS, Halogen Free

Customers who bought this product also bought

Digital Compass GY-273 Compas Magnetometer

Three-axis electromagnetic field sensor module GY-273 including the HMC5883L chip that specifies the direction of the magnetic field of the ground.
Digital Compass GY-273 Compas Magnetometer features:

  • Supply voltage: 2.16 - 3.6 VDC,
  • I2C interface with SCL, SDA,
  • signals - Measurement range: 1.3 to 8 Gauss,
  • Measurement resolution: 12 bits,
  • Measurement accuracy: 0.73 - 4.35 Gauss,
  • Transmission speed 400kHz, 
  • Sensitivity 230-1370 LSB / Gs,
  • Output frequency: 75Hz,
  • DRDY pin interruption,
  • Dimensions of 18 mm x 13 mm.

M0179

Regular price €3.13 -€0.50 Price €2.63

NE555P DIP8 Precision Timer Integrated Circuit

NE555P DIP8 Precision Timer Integrated Circuit features:
- Blister: DIP8
- Number of pins: 8
- Step between pins: 2.54 mm
- Manufacturer: Texas Instrument - Input voltage VCC: 4.5 - 16 VDC
- THRES voltage level: 2.4 - 11.2 VDC
- TRIG voltage level: 1.1 - 5.6 VDC
- RESET voltage level: 0.3 - 1 VDC
- DISCH voltage level change out of state: 0.15 - 0.4 nA
- CONT voltage (open circuit): 2.6 - 11 VDC
- Low level output voltage: 0.1 - 0.4 V
- High level output voltage: 2.75 - 13.3 V - Output current I (O): ± 200 mA
- THRES current: 30 - 250 nA
- TRIG current: 0.5 - 2 μA
- RESET current: -0.4 - 0.4 μA
- Current change DISCH out of state: 20 - 100 nA

T0061

Price €0.65

Digital Light Intensity Sensor with Photo Resistance with LM393 Controller

This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,
The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.
The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.
It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features:
- Operating voltage: 3.3 - 5 V
- Input current: 50 mA
- Use a very sensitive photo resistance
- Use a LM393 wide voltage comparator, high quality output signal
- Adjustable potentiometer can regulate the brightness of detected light

M0156

Price €1.40

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

P0008

Price €1.15
€3.26
Save €1.09 €2.17

2,17 tax excl.

1
Last 3 items
Regular price €3.26 Price €2.17

Order until 4pm we will send today
30 days return