Flux Welding Paste 20g Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C. - Flux paste based on activity rosin medium. - Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints . Operating temperature up to 350 C. Code Q0025 Available Price €1.89
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.45 -€0.50 Price €0.95
3S BMS 25A 12.6V 18650 PCM PCB Circuit Charging Module. In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0106 Available Price €4.49
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0013 Available Price €0.08
JST Male Connector 15cm AWG18 This connector can be used in most modeling projects. It is ideal for small Lipo and NiMH connection. JST Male Connector 15cm AWG18 features: - Type: JST male connector for RC BEC Lipo - Color: - Black: low power polarity - Red: high power polarity - Length: 20cm Code K0153 Available Price €1.09
Dupont Connector 2.54mm Female Dupont Connector 2.54mm Female features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0110 Backorder Price €2.19
Resistor 4,7M Ohm 5% 0,25W 1/4W Resistor 4,7M Ohm 5% 0,25W 1/4W features:-4.7M Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0033 Available Price €0.08
Car battery tester and charger Konnwei KW510 The Konnwei KW510 is an advanced multi-function device that uses state-of-the-art technology to allow you to easily, quickly and accurately measure the actual cold start capability, battery condition and common faults in the vehicle's starting and charging systems. The KW510 is particularly useful for workshops as it can accurately detect the problem, allowing the vehicle to be repaired quickly. Code H0586 Available Price €69.95
Battery charger for 12V 3A gel batteries Battery charger for 12V gel batteries with battery state of charge monitoring. Alligator clip connectors. Code A0131 Available Price €10.90
Wireless charger module 5V 2V with transmitter coil. Wireless charging and powering of small electronic products. It is designed for small size, ease of use, high performance and low price. The main purpose of the module is to be used in the initial phase of projects such as mobile electronic products. Code A0174 Available Price €8.95
Charger for 4 Ni-MH R6/AA,R03/AAA Rechargeable Batteries everActive NC-450 The European plug-in charger for charging 4 rechargeable batteries at the same time, each charge is individually displayed. Advanced processor controls the charging process with "delta V" function. Code A0133 Available Price €15.99
Battery charger for 12V 1.5A gel batteries Battery charger for 12V gel batteries with battery state of charge monitoring. Alligator clip connectors. Code A0135 Available Price €9.95
5S BMS 25A 21V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0108 Available Price €4.69
4S BMS 25A 16.8V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0107 Available Price €4.59
Charger 4 x 9V 6F22 with EU Power Supply Cable Charger 4 x 9V 6F22 with EU Power Supply Cable features: The everActive NC 109 charger is a unique, specialized design that allows you to charge from 1 to 4 pieces of 9V Ni-MH batteries - each cell is charged individually.It allows you to charge up to 4pcs of 9V batteries simultaneously, in any configuration / combination, with any capacity, any manufacturer.The charger has 4 independent charging channels.The most important features: of the NC109 loader:- quick charging of a large number of batteries simultaneously - ideal for industrial and professional applications,- individual LED indicator of charger work for each cell - with full charge signaling,- 100-240V AC power adapter included, optionally a 12V car adapter is available, Code A0101 Available Price €17.99
TP4056 Lithium Battery Charger Module 5V Mini USB TP4056 Lithium Battery Charger Module 5V mini USB features: - Based on TP4056ES regulator - Lipo mini USB Li-Ion charger - Input Voltage: 4.5V - 5.5 VDC - Full charge voltage: 4.2V +/- 1.5% - Max Output Current: 1A - Indicator LED: charging red, charging green - Operating temperature: -10ºC to + 85ºC - IN + and IN- connection for electronic circuits - Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A - Measurements: 25x19x5 mm - Ideal for 18650 batteries Code A0008 Available Price €0.99
Battery charger BMS 3,7-96V 10A - Automatic charge controller module This 3.7-96V 10A battery charger is an automatic charge controller module that prevents the battery from dropping below a voltage level, the value of which is adjustable. It is suitable for 1.5 to 120V batteries, as using it will save time and energy. Code A0130 Available Price €10.90
Car battery tester and charger Konnwei KW510 The Konnwei KW510 is an advanced multi-function device that uses state-of-the-art technology to allow you to easily, quickly and accurately measure the actual cold start capability, battery condition and common faults in the vehicle's starting and charging systems. The KW510 is particularly useful for workshops as it can accurately detect the problem, allowing the vehicle to be repaired quickly. Code H0586 Available Price €69.95
Battery charger for 12V 3A gel batteries Battery charger for 12V gel batteries with battery state of charge monitoring. Alligator clip connectors. Code A0131 Available Price €10.90
Wireless charger module 5V 2V with transmitter coil. Wireless charging and powering of small electronic products. It is designed for small size, ease of use, high performance and low price. The main purpose of the module is to be used in the initial phase of projects such as mobile electronic products. Code A0174 Available Price €8.95
Charger for 4 Ni-MH R6/AA,R03/AAA Rechargeable Batteries everActive NC-450 The European plug-in charger for charging 4 rechargeable batteries at the same time, each charge is individually displayed. Advanced processor controls the charging process with "delta V" function. Code A0133 Available Price €15.99
Battery charger for 12V 1.5A gel batteries Battery charger for 12V gel batteries with battery state of charge monitoring. Alligator clip connectors. Code A0135 Available Price €9.95
5S BMS 25A 21V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0108 Available Price €4.69
4S BMS 25A 16.8V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0107 Available Price €4.59
Charger 4 x 9V 6F22 with EU Power Supply Cable Charger 4 x 9V 6F22 with EU Power Supply Cable features: The everActive NC 109 charger is a unique, specialized design that allows you to charge from 1 to 4 pieces of 9V Ni-MH batteries - each cell is charged individually.It allows you to charge up to 4pcs of 9V batteries simultaneously, in any configuration / combination, with any capacity, any manufacturer.The charger has 4 independent charging channels.The most important features: of the NC109 loader:- quick charging of a large number of batteries simultaneously - ideal for industrial and professional applications,- individual LED indicator of charger work for each cell - with full charge signaling,- 100-240V AC power adapter included, optionally a 12V car adapter is available, Code A0101 Available Price €17.99
TP4056 Lithium Battery Charger Module 5V Mini USB TP4056 Lithium Battery Charger Module 5V mini USB features: - Based on TP4056ES regulator - Lipo mini USB Li-Ion charger - Input Voltage: 4.5V - 5.5 VDC - Full charge voltage: 4.2V +/- 1.5% - Max Output Current: 1A - Indicator LED: charging red, charging green - Operating temperature: -10ºC to + 85ºC - IN + and IN- connection for electronic circuits - Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A - Measurements: 25x19x5 mm - Ideal for 18650 batteries Code A0008 Available Price €0.99
Battery charger BMS 3,7-96V 10A - Automatic charge controller module This 3.7-96V 10A battery charger is an automatic charge controller module that prevents the battery from dropping below a voltage level, the value of which is adjustable. It is suitable for 1.5 to 120V batteries, as using it will save time and energy. Code A0130 Available Price €10.90